Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
100.0mm REF
HP Netserver LP 2000r Technical Reference Label
CAUTION!
A Netserver
Power Supplies
C Control Panel
Flexible Disk Drive
Power Switch
Do not operate with power
CHA_FAN2
supply slot empty. Close the
Air Flow
System Board
hp netserver lp2000r
Disk 0
Disk 3
slot with a filler panel or a
Guide
Disk 1
Disk 4
second power supply.
PCI Cage
Disk 2
Disk 5
SCSI Cage
Reset
Power
SCSI
Power
Temperature/Fans
Supply Activity
Slot 3
G Standard SCSI Cabling
Power Supply Removal
Slot 4
Control Panel LED Definitions
Slot 5
HDD 0
2
Power
Steady green when operating normal y. Flashing green at 1 Hz rate in sleep mode.
3
HDD 1
3
SCSI A
External
SCSI B
4
SCSI Activity
Flashing green when there is SCSI activity. Off when there is no activity.
SCSI
CHA_FAN1
Disks
Steady green when drive is present. Off when drive is not present. Steady red for faulty
HDD 2
drive or rebuild failure. Alternating green and red at 1 Hz rate for SCSI rebuild.
Flexible
1
SCSI Cage
Alternating green and red at 3 Hz rate indentifies drive.
5
IDE-1
2 CD-ROM
Disk Drive
HDD 3
Temperature/Fans
Steady green for normal operation. Steady red indicates overtemperature, or fan failure.
CD-ROM
Slot 0
Alternating green and red indicates warning.
See Panel B
HDD 4
Slot 1
for Control Panel
Power Supply
Steady green indicates normal operation. Alternating green and red indicates power
FDD
1 FDD
1. Press in to release latch
Slot 2
Front Panel
supply warning. Steady red indicates power supply failure.
HDD 5
System Board
2. Pull down latch
3. Slide Power Supply out
Power Supply Insertion
B System Board
Serial B
D
Duplex SCSI Cabling
Rear Panel
Activity
Speed
LED
LED
HDD 0
LAN B
LAN A/Mgmt
Parallel
Battery
Video
Serial A/ Mgmt.
HDD 1
3
2
SCSI A
USB (2)
Enlarged LAN
Connector
Mouse (upper)
Power
Power
AC Power for PS 1
HDD 2
Keyboard (lower)
Supply 1 Supply 2
IDE-1
2 CD-ROM
Mouse
USB (2)
Parallel
Serial B
PCI Slots (3)
HDD 3
HDD 4
5
SCSI B
FDD
1 FDD
PCI
Processor 1
1
Riser
B
Card
HDD 5
CAUTION!
System Board
1. Press in firmly
2. Push up latch to secure
Use a new thermal
A
pad when reinstal ing
a heatsink
DAC Duplex SCSI Cabling
1
0
IDE-2
Processor 2
Keyboard
Video
LAN B
HDD 0
Cables Type
0
Power LEDs
External SCSI
.
AC Power
0
Serial A/Mgmt
LAN A/Mgmt
Connector
Flexible Disk
HDD 1
3
1
Power
m
Integrated
for PS 2
SCSI 0
Cable
External
Connector
SCSI B
4
Remote
SCSI
IDE CD-ROM
m
HDD 2
2
Assistant
Cable
Board
Rear Panel LED Definitions
DAC
R
0
IDE-1
2
CD-ROM
3
SCSI Cable
HDD 3
Power
E
Steady green indicates normal operation. Flashing green indicates Standby Mode.
PCI Cage
1
Steady amber indicates power supply failure.
Int / Ext SCSI
F
Connector
DIMMs
4
HDD 4
2
5
SCSI 1
FDD
1
FDD
Cable
LAN Activity Steady green indicates link is valid. Flashing green indicates activity on LAN.
3
HDD 5
5
SCSI Cable,
LAN Speed
Steady amber indicates link rate of 100mbps. Off indicates link rate of 10mbps.
System Board
Long
FDD
SCSI B
Not Used (Default = Off)
Boot Order
IDE-1
BIOS Recovery
SCSI A
Clear Password
O
E Mass Storage Device Locations
Selected HP Accessories
1. IDE CD-ROM
H Service Information
For other tested accessories, download the Order Assistant
P
Air Flow
Configuration
E
Clear CMOS
2. Flexible Disk Drive
N
Guide
Not Used (Default = Off)
Switch
and Settings
from the HP Web page.
Electronic Support Services
Audience Assumptions
3. Hard Drive
Not Used (Default = Off)
Connector
• I nternet Web Page http://www.hp.com/go/netserver
This Technical Reference Label is for trained service personnel.
4. Bootable Cards
Not Used (Default = Off)
Device
Location (in order
Device Settings
Not Used (Default = Off)
• I nternet FTP f tp://ftp.netserver.hp.com
Hewlett-Packard Company assumes you are qualified in the
5. Network Connection
of recommendation)
Open = Off Closed = On
• C
ompuserve Library GO HPPC
servicing of computer equipment and trained in recognizing
hazards in products with hazardous energy levels.
Flexible Disk Drive
See Panel A
Factory installed
• H
P Navigator CD
Electrostatic Discharge (ESD) Warning
Support Questions
To avoid catastrophic or hidden damage to components,
F
Standard IDE CD-ROM Drive
See Panel A
Factory Installed
Memory
4MB of standard video memory is
• H
P-Authorized Reseller
wear a wrist strap and use a static-dissipative work surface
provided with the embedded video
HP Accessory 9 GB HDD or
Slot 0 through 5
Drives may be instal ed in Slot 0
• C
ompuserve Discussion Forum GO HPPC
connected to the chassis when handling components. Use
an antistatic service kit, such as 3M
® 8501/ 8502/8505 or
controller.
Use only PC 133 HP DIMMs.
HP Accessory 18 GB HDD or
through 5.
• U
S / Canada Phone Support 1-970-635-1000
HP Accessory 36 GB HDD
equivalent.
• E
urope Phone Support
(+31-20) 581-3330
DIMMs may be installed in any
The LP 2000r can support up to 4GB.
This information is subject to change without notice and
combination in any DIMM socket.
Standard Dual SCSI Control er
Embedded
SCSI ID 7
(Netherlands)
HP has offices in over 100 countries.
is provided without warranty.
Check your local telephone directory.
DIMM sizes supported are 128MB,
© Copyright 2000 Hewlett-Packard Company
When handling DIMMs observe
256MB, 512MB, and 1GB.
anti-static precautions.
See documentation with each device for further configuration information.
P1824-80221
Label Manufacturer to print part
number in Code 39 barcode here