Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
11MakeExternalConnections
Monitor
Keyboard
Make external connections, such as the monitor, keyboard, and mouse cables, UPS,
Mouse
and the AC power cord to the appropriate connectors on the rear of the chassis as
instructed in the Rack Cabling Guide Reference for the HP NetServer LH 3r.
AC Power
Connector
Rear View
Configure the HP NetServer
! Use the manual NOS installation if you are installing a NOS other
121. BoottheHPNavigatorCD-ROM:Turnonthe
monitor. Press the power-on button on the HP NetServer,
than Novell NetWare / IntranetWare or Microsoft Windows NT
and press the eject button on the CD-ROM drive. Place the
Server, or if you have replaced accessory components (for
HP Navigator CD-ROM in the drive, and close the drive.
example, if you replaced an HP network interface controller board
Press the Reset button. If the system fails to restart, follow
with a third-party board, use the manual NOS installation).
the instructions on the screen.
9. View Configuration Advisories: Read the Configuration
Advisories and print them if necessary. Make any changes suggested
NOTE
If you have installed an ISA non-Plug-and-Play
in the advisories.
accessory board, you must reserve system
resources for it by using the Setup Utility. Start
10. Configure Remote Management: If you plan to manage the
the Setup Utility by pressing function key [F2]
HP NetServer LH 3 remotely, refer to the HP NetServer Server
when prompted during the boot process.
Management Reference Guide for instructions. Select "Configure
Remote Management" on the Navigator screen to configure
When the Setup Utility starts, select
Integrated Remote Assistant.
"Configuration," and then select "ISA non-Plug-
11. Show System Information: Select "View System Information"
and-Play Devices." Use the arrow keys to
to get information about accessory boards and devices. Select "View
highlight a selection, press ENTER to display
Resources" to view used and available system resources.
its options, and use the +/- keys to change
values. When you have finished, save the
12. Configure Mass Storage. This NetServer is shipped with the
changes and exit the utility.
hot-swap mass storage device(s) unconfigured. To configure the
drive(s), do one of the following:
For more information about reserving system
!
resources, refer to Information Assistant and to
Run HP NetRAID Assistant to configure one or more RAID logical
"Configuring ISA Non-Plug-and-Play Board" in
drives. To run HP NetRAID Assistant, select "Execute" from the
Chapter 4, "Accessories," in the HP NetServer
Configure Disk Array screen.
LH 3/LH 3r User Guide.
! Exclude SCSI A Channel from the integrated HP NetRAID
controller, as follows:
(If the system hangs before the Setup Utility
a. Restart the HP NetServer.
starts, remove the ISA non-Plug-and-Play
board, run the Setup utility to reserve system
b. Press function key [F2] when prompted on the boot screen.
resources for it, then reinstall the board.)
c. When the SETUP utility menu is displayed, use the up and down
keys to highlight the "Include SCSI A Channel [Yes]" selection.
d. Use the + and - keys to change it to "Include SCSI A Channel
When HP Navigator starts, you can set the time and date,
[No]."
and change the display language.
e. Press function key [F10] to save the configuration and exit the
2. Read the Readme File: Select "Readme File" from the
utility program.
HP Navigator Main Menu. The Readme file contains the
f. Answer "Yes" to the question "Save Configuration and Exit
latest information to help you install your HP NetServer.
Now?" The HP NetServer will reboot, and HP Navigator will
restart.
3. Run Diagnostic Assistant (Optional): To verify the
HP NetServer hardware as shipped, run Diagnostic
13. Install the NOS: If you selected the HP automated NOS
Assistant from the HP Navigator CD-ROM. Select
installation process, you will be guided through the process by a
"NetServer Utilities" from the HP Navigator Main Menu, and
series of HP display screens:
then select "Diagnostic Assistant" from the NetServer
! Install Utility Partition: This step creates an 8 MB disk partition on
Utilities menu.
the server boot hard disk drive where HP Navigator will copy
4. Install Information Assistant: Information Assistant
troubleshooting and other utilities. The utility partition is not
will help you install your HP NetServer. It is easier to use
available under SCO UNIX. Select "Execute" on the Install Utility
from a stand-alone system, rather than from the HP
Partition screen to install the partition.
NetServer you are installing. Install Information Assistant
! Execute Card Utilities: Select "Execute" on the Execute Card
from the HP NetServer Online Documentation CD-ROM
Utilities screen to run the accessory board configuration utilities.
onto the client system that you will be using to manage your
! Follow the instructions on the screen and in the network operating
HP NetServer.
system's installation instructions to perform the manual NOS
5. Visit Order Assistant (optional)
installation.
on the Internet at
!
http://www.hp.com/go/netserver
For Manual NOS Installation Only: Before you perform a manual
NOS installation, print out instructions and create NOS-specific
Order Assistant lists HP accessories, cables, and
drivers diskette(s), as follows:
connectors for your HP NetServer.
A. Create Drivers Diskette(s): On the Create Drivers Diskette(s)
6. Run Configuration Assistant and Installation
screen, select Create Drivers Diskette(s) to create one or more
Assistant: If you want to change the language, select
customized diskettes containing HP drivers and configuration
"Set Preferences" from the HP Navigator main menu and
files to use when you install the NOS.
choose a language. Select "Configuration and Installation
B. Print and Read Instructions: On the Show NOS Installation
Assistant." Select "Express" from the next screen to begin
Instructions screen, select "Save to Disk" to copy the NOS
the "Express" mode of configuration.
installation instructions to disk. Then print them from disk. Read
the instructions first, and then follow them to manually install the
"Custom" configuration mode and "Replication"
NOS.
configuration mode are also available. Refer to the HP
!
NetServer LH 3/LH 3r User Guide for details.
Install NOS:
A. Automated NOS Installation: For certain versions of Novell
7. Choose a NOS: Select the NOS you will install, and the
NetWare / IntranetWare or Microsoft Windows NT Server,
version, if necessary. Installing the optional IntranetWare
Configuration Assistant formats and partitions the hard disk
NOS, which is part of the HP NetServer Software Option
drive. Installation Assistant then guides you through the NOS
Package, requires a decryption key, obtained in panel 2,
installation and configures the NOS with the appropriate drivers
"Obtain IntranetWare Key."
for the HP-bundled configuration.
8. Select the NOS installation mode: If you select
B. Manual NOS Installation: Follow the instructions on the screen
certain versions of Novell NetWare / IntranetWare or
and the network operating system installation instructions that
Microsoft Windows NT Server, you will be asked, "Would
you printed.
you like to use HP's automated mode of NOS installation?"
14. Install HP TopTools: Refer to the HP NetServer Server
! Select "Yes" to choose automated NOS installation for
Management Reference
,
Guide and install HP TopTools.
first-time installation of Novell NetWare / IntranetWare or
15. Refer to Information Assistant on the
Microsoft Windows NT Server on a factory-configured HP
HP NetServer Online
NetServer.
Documentation CD-ROM, for further information about your
NetServer.