If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Switching on and off 1. Connect the plug to the power supply. 2. Push the left-hand side “I” of the sealed on/off switch (1) to start the motor. 3. Push the right-hand side “O” of the sealed on/off switch (1) to stop the motor. 4. Hold the tool securely and make sure that you have full control at all times. Using the san

Paper clamp 7. Dust extraction adaptor 8. Washable dust bag 9. Removable side clip (x 2) (for carbon brush access) 10. Sandpaper hole punch 11. Power ON neon light 7 3 2 9 1 11 4 8 10 5 6 Switching on and off 1. Connect the plug to the power supply. 2. Push the on/off switch (1) forward to start the motor. CAUTION. Make sure the tool is not resting on any surface when it is switched on. 3. Pull the on/off switch (1) back to stop the motor. 4. Hold the tool securely and make sure that you have fu

Ensure that the handle is fully screwed in place and firm. Disc guard WARNING. Switch off the grinder and disconnect it from the power point. NOTE. Grinding operations normally require the angle grinder to be held with the grinding disc parallel to the plane of the workpiece whilst cutting operations normally require the angle grinder to be held with the cutting disc at right angles to the workpiece. Take the time to find the best combination of front handle and slimline handle positions to suit

This angle grinder is designed as a dry grinder/cutter. Failure to observe this warning could result in a fatal shock. Holding and guiding the tool 1. Always clamp the workpiece. 2. Do not overload the tool so that the disc slows down. Let the tool do the work rather than applying pressure. The weight of the tool alone provides sufficient pressure. 3. Cutting and grinding discs become very hot when in use. Take care not to touch them until they have cooled down. 4. Hold the tool securely and mak

11/3 HP BELT/DISC SANDER BD1500 INSTRUCTION MANUAL 1/3 HP BELT/DISC SANDER BD1500 INSTRUCTION MANUAL ContentsContents Introduction 3 Description of symbols 3 Specifications 3 General safety rules 4 Additional safety rules for belt & disc sanders 5 Unpacking 6 Accessories 7 Know your product 8 Getting to know your belt and disc sander 9 Mounting belt and disc sander to workbench 9 Installing sanding disc and guard 9 Installing work support 9 Installing table assembly 10 Auxiliary mounting for ver

• Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris INSTRUCTION MANUAL 1/5 HP / 2/5 HP / 2/3 HP / 1/2 HP Bench Grinders 031222 ED8 DR BG125A BG150A BG200A NTS2000A • Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris INSTRUCTION MANUAL 1/5 HP / 2/5 HP / 2/3 HP / 1/2 HP Bench Grinders 031222 ED8 DR BG125A BG150A BG200A NTS2000A Contents Contents Warranty 2 Introduction 3 Environmental protection 3 Descr

If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Connecting to the power supply The GMC Bench Grinders covered in this manual are designed to operate from a standard household supply of 230-240V AC. Prior to plugging in the tool, check the rating label on the rear of the grinder and ensure that it states the tool’s operating voltage is 240V. All the grinders are of Cla

• Replace a cracked or suspect wheel. • Always allow a new wheel to run for a few minutes at full speed before using it. Stand to one side at start up. • Check that the wheel rotates freely each time before start up. • Do not use the grinder unless all the guards are properly fitted and secure. • Check that the tool rests are properly adjusted before commencing use. • Do not overload the grinder. Allow the grinder to run at full speed, or close to full speed during use. • Never apply excessive p

It is strongly recommended that the grinder be firmly mounted to a bench or stand for safe operation. The base of the grinder has a 7mm hole in each corner. These holes accept screws or bolts up to 6mm diameter. Mounting screws are not supplied with the unit. Where the grinder is to be mounted on to a steel work bench, it is advisable to place a piece of timber between the bench and grinder then screw or bolt through the grinder and timber into the bench. This further assists to reduce vibration

INSTRUCTION MANUAL 150mm (6") 1/2HP / 200mm (8") 3/4HP Bench Grinders • Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris BG612HPL BG834HPL 031222 ED7 DR INSTRUCTION MANUAL 150mm (6") 1/2HP / 200mm (8") 3/4HP Bench Grinders • Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris BG612HPL BG834HPL 031222 ED7 DR Contents Contents Warranty 2 Introduction 3 Environmental protection Description of symbols Spec