If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. MINIMUM GAGE FOR CORD SETS Total Length of Cord in Feet (Meter) 0 – 25 26 – 50 51 – 100 101 – 150 (0 – 7.6) (7.9 – 15.2) (15.5 – 30.5) (30.8 – 45.7) Ampere Rating AWG More Not More Than Than 0 – 6 18 16 16 14 6 – 10 18 16 14 12 10 – 12 16 16 14 12 12 – 16 14 12 Not Recommended WARNING: AVOID ELECTRICAL SHOCK HAZARD. NEVER USE THIS TOOL WITH A DAMAGED OR FRAYED ELECTRICAL CORD OR EXTENSION CORD. INSPECT ALL

To keep the double insulation system effective, follow these precautions: a. Only a AUTHORIZED JOHN DEERE DEALER should disassemble or assemble this power tool, and only genuine JOHN DEERE replacement parts should be installed. b. Clean the exterior of the power tool only with a soft cloth moistened with soapy water, and dry thoroughly. Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve. 4 1/4-Inch Disc Grinder Operator's Manual IMPORTANT SAFETY IN

(See Figure C, and Assy. Diagram.) BRAKE PIN (#18) SIDE HANDLE (#20) WOOL COVER (#45) BRUSH CAP (#40) CARBON BRUSH (#41) BRUSH HOLDER (#42) VARIABLE SWITCH (#31) BACK HANDLE (#39) POWER CORD (#36) FIGURE C OPERATING INSTRUCTIONS NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 12 of this manual. SKU 46507 PAGE 8 To Attach The Rubber Backing Plate And Sandpaper: To Attach The Rubber Backing Plate And Sandpaper: . Caution: Prior to installing the Rub

To prevent serious injury from accidental operation: Turn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before assembling or making any adjustments to the tool. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Assembly TO PREVENT SERIOUS INJURY: Do not operate this tool with one hand only or without the Auxiliary Handle properly installed. Attach the S

3. For safest operation, it is recommended that only these accessories be used with this product: Abrasive Cut-Off Discs and Wheels, Flap Wheels, Wire Brushes, Wire Wheel Brushes. 4. Always use an approved and proper guard when using the above mentioned accessories. Each accessory must have the correct arbor size and must fit properly on the Gear Shaft. Make sure accessories are tightened down securely. 5. Always disconnect from power source before adding or removing accessories. Use a cloth or

The operator must understand that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SAVE THESE INSTRUCTIONS ASSEMBLY AND OPERATING INSTRUCTIONS NOTE: For additional references to the parts listed in the following pages, refer to the Assembly Diagram on page 9. To Attach A Quick Connector: 1. WARNING! Prior to performing any assembly and/or adjustment procedures, make sure the air supply hose (not included) is disconnected from the

Copyright 2004 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call 1-800-444-3353. Manual Revised 11h ®.. © PRODUCT SPECIFICATIONS UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 9 are included. If any parts are missing or broken, please call Har

Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. straight line air sander Visit our website at: Email our technical support at: tech@harborfreight.com ITEM 91773 REV 11l Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL. When unpacking, make sure that the product is

Do not use the tool if any switch does not turn On and Off properly. 16. Guard against electric shock. Prevent body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerator enclosures. 17. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 18. Do not operate tool if under t

Introduction Congratulations on the purchase of your new John Deere 1/4-Inch Right Angle Grinder! You can be assured your angle grinder was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance. John Deere 1/4-Inch Right Angle Grinder is designed for grinding and deburring operations in confined areas. This rear exhaust tool features a built-in regulator for convenient speed control and a lock-off lever