22. Channel 1 & 2 TRS Input - Channel one & two 1/4” female jacks. Excepts either a balanced or unbalanced plug. See page 9 for more details. 23. Mode Switch - This switch controls the amplifier’s operating mode. The amplifier can operate in three different modes; Mono Bridge, Stereo, or Parallel Mono. The amplifier is shipped in stereo mode. 24. Air Vents - These vents allow hot air to exit the amp. Do not place anything in front or obstruct these vents. 25. AC Cord - Plug this cable into a sta

If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product. If any accessories are shipped with the product, American Audio® shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which American Audio® concludes, after inspection, affects the reliability

• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of elec- trical shock and fire in case of an internal short. • Disconnect main power before making any type of connection • Do not remove the cover under any conditions. There are no user serviceable parts inside. • Never plug this unit in to a dimmer pack. • Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this dev

Connect your speakers to the outputs on the rear of the amplifier. Be sure that your front gain controls are turned down to their lowest level (full counter-clockwise). Turn your amp on. Turn your input source level up. Use your front gain controls to regulate the output volume. Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable. Mono Bridge Operation - Page 15/Figure 15 details a mono bridge set-up. Be sure your amplifier and all other audio equ

It will allow brief clipping of peaks and will only activate when continuous, hard clipping occurs. During excessive clipping the limiter will reduce the audio signal enough to minimize the amount of clipping. When the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction. The limiter has a fixed threshold and can not be adjusted. Safe Power Levels at Different Output Loads: 8-Ohm Loads: The amplifier can operate at practically any power level

Excepts either a balanced or unbalanced plug. See page 9 for more details. 24. Mode Switch - This switch controls the amplifier’s operating mode. The amplifier can operate in three different modes; Mono Bridge, Stereo, or Parallel Mono. The amplifier is shipped in stereo mode. 25. Ground On/Off Switch - If hear a hum or any interference, put the Ground switch in the “On” postion . 26. Channel 2 Speakon Output - Optional speaker output connections. Use pins 1+ and 1- of this 4-pole Speakon connec

This LED may glow when the unit has been turned off, this is normal. 4. Channel 1 Signal Indicators - These green and yellow LED’s will glow according to the average signal output. 5. Function Indicators - These indicators detail the operating mode of the amplifier. These LEDs will also function as a power indicator. 6. Power Switch - This switch is used to control the units main power. 7. Channel 2 Signal Indicators - These green and yellow LED’s will glow according to the average signal output

• Do not spill water or other liquids into or on to your unit. • Do not attempt to operate this unit if the power cord has been frayed or broken. • Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of elec- trical shock and fire in case of an internal short. • Disconnect main power before making any type of connection • Do not remove the cover under any conditions. There are no user serviceable parts inside. • Never plug this u

USING THREE SPEAKERS, THEY MUST BE RATED EACH AT 8 OR MORE OHMS. POUR ASSURER LA FIABILETE ET OBTENIT UNE PERFORMANCE OPTIMALE, NESOUMETTE JAMAIS L’AMPLIFICATEUR A UNE CHARGE D’IMPEDANCE TOTALE INFERIEURE A 2 OHMS, NI AVEC UN H.P. NI EN COMBINAISON DES H.P. AVEC UN H.P., IL FAUT UNE CHARGE D’IMPEDANCE MINIMUM DE 2 OHMS. AVEC DEUX H.P., FAUT POUR CHAOUN UNE CHARGE D’IMPEDANCE MINIMUM DE 4 OHMS. AVEC TROIS H.P., FAUT POUR CHAOUN UNE CHURGE D’IMPEDANCE MINIMUM DE 8 OHMS. CONTENTS: Safety Precaution

Red is positive signal and Black is negative signal. 31. Channel 1 Speakon Output - Optional speaker output connections. Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your speaker’s Speakon input jack. 32. Filter Switch - This switch controls the amplifier’s filter mode. The amplifier can operate in three different filter modes; High Pass, Low Pass, and By-Pass. 33. Sensitivity Switch - This switch lets you choose the input sensitivity. 34. Channel 1 TRS Input - Channel one 1