Stimmen - 6, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: American Audio Dateigröße: 5.72 mb Dateiname: vlpseries.pdf Unterrichtssprache:

Fotos und technische Daten  American Audio  VLP600

Excepts either a balanced or unbalanced plug. See page 9 for more details. 24. Mode Switch - This switch controls the amplifier’s operating mode. The amplifier can operate in three different modes; Mono Bridge, Stereo, or Parallel Mono. The amplifier is shipped in stereo mode. 25. Ground On/Off Switch - If hear a hum or any interference, put the Ground switch in the “On” postion . 26. Channel 2 Speakon Output - Optional speaker output connections. Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your speaker’s Speakon input jack. 27. Channel 2 Output Jack/5 way Binding Post - Connect to your speaker’s input jack. Red is positive signal and Black is negative signal. 28. AC Cord - Plug this cable into a standard wall outlet. Check that the voltage in your area matches the amplifiers required voltage. 29. Fuse Holder - This housing stores a 15 amp GMA protective fuse for the VLP 600 and 30 amp GMA protective fuse for the VLP 1500. Never defeat the fuse, the fuse is designed to protect the electronics in the event of severe power fluctuations. Always be sure to replace the fuse with an exact match as the one being replaced, unless otherwise told to do so by an authorized American Audio ® service technician. 30. Channel 1 Output Jack/5 way Binding Post - Connect to your speaker’s input jack. Red is positive signal and Black is negative signal. 31. Channel 1 Speakon Output - Optional speaker output connections. Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your speaker’s Speakon input jack. 32. Filter Switch - This switch controls the amplifier’s filter mode. The amplifier can operate in three different filter modes; High Pass, Low Pass, and By-Pass. 33. Sensitivity Switch - This switch lets you choose the input sensitivity. 34. Channel 1 TRS Input - Channel one 1/4” female jack. Excepts either a balanced or unbalanced plug. See page 9 for more details. 35. Channel 1 XLR input - Channel one 3-pin XLR balanced input jack. See page 9 for more details. 36. Limiter Switch - This switch is used to limit the input level. Use this function to avoid damage to your speakers. ©American Audio® - - VLP Series™ Power Amplifier User Manual Page 7 Rear Panel Control 37 44 43 42 41 40 39 38 46 45 50 49 48 47 Figure 4 51 37. AC Cord - Plug this cable into a standard wall outlet. Check that the voltage in your area matches the amplifiers required voltage. 38. Channel 1 TRS Input - Channel one 1/4” female jack. Excepts either a balanced or unbalanced plug. See page 9 for more details. 39. Channel 1 XLR input - Channel one 3-pin XLR balanced input jack. See page 9 for more details. 40. Mode Switch - This switch controls the amplifier’s operating mode. The amplifier can operate in three different modes; Mono Bridge, Parallel Mono, or Stereo. The amplifier is shipped in stereo mode. 41. Channel 2 XLR Input - Channel two 3-pin XLR balanced input jack. See page 9 for more details. 42. Channel 2 TRS Input - Channel two 1/4” female jack. Excepts either a balanced or unbalanced plug. See page 9 for more details. 43. Filter Switch - This switch controls the amplifier’s filter mode. The amplifier can operate in three different filter modes; High Pass, Low Pass, and By-Pass. 44. Sensitivity Switch - This switch lets you choose the input sensitivity. 45. Ground On/Off Switch - If hear a hum or any interference, put the Ground switch in the “On” postion . 46. Channel 2 Output Jack/5 way Binding Post - Connect to your speaker’s input jack. Red is positive signal and Black is negative signal. 47. Channel 1 Output Jack/5 way Binding Post - Connect to your speaker’s input jack. Red is positive signal and Black is negative signal. 48. Channel 1 Speakon Output - Optional speaker output connections. Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your speaker’s Speakon input jack. 49. Channel 2 Speakon Output - Optional speaker output connections. Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your speaker’s Speakon input jack. 50. Cooling Fans - Dual high speed cooling fans 50. Fuse Holder - This housing stores a 8 amp GMA protective fuse. Never defeat the fuse, the fuse is designed to protect the electronics in the event of severe power fluctuations. Always be sure to replace the fuse with an exact match as the one being replaced, unless otherwise told to do so by an authorized American Audio® service technician. ©American Audio® - - VLP Series™ Power Amplifier User Manual Page 8 Set Up INPUTS - The VLP Series amplifier allows you to use two types of input connector per a channel, a XLR jack for balanced connections and a 1/4” female jack that will accept balanced and unbalanced connectors. Use these connections to connect the output signal from a mixer, cross-over or EQ to your VLP Series amplifier. A balanced connection is recommended for cable runs longer that 20ft. When constructing your own XLR cables follow the pin configuratio...

Herunterladen

Geben Sie zwei Ziffern: