. . . . . . . . . . . . . . . . . . . . . . . .1 Safety Guidelines . . . . . . . . . . . . . . . . . . . . . .2 Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . .2 Important Safety Information . . . . . . . . . .2 Getting To Know Your Compressor . . . . .4 Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Maintenance. . . . . . . . . . .

Grounded Outlet Grounding Pin Figure 2 - Grounding Method MOISTURE IN COMPRESSED AIR Moisture in compressed air will form compressor pump. When humidity is high use for an extended period of time, this moisture hose. When using a paint spray or sandblast the tank through the hose, and out of the gun material. IMPORTANT: This condensation will cause water spots in a paint job, especially when spraying other than water based paints. cause the sand to cake and clog the gun, rendering it ineffective

M a i n t e n a n c e Disconnect power source then release all pressure from the system before attempting to install, service, relocate or perform any maintenance. Service should be performed by an authorized service representative. 3 Oilless Compre s s o r s M a i n t e n a n c e ( C o n t i n u e d ) The compressor should be checked often for any visible problems and the following maintenance procedures should be performed each time the compressor is used. ASME SAFETY VALVE Do not remove or at

Make sure to tighten fittings, bolts, etc., before putting unit into service. In case of questions, damaged or missing parts, please call 1-800-543-6400 for customer assistance. Have the date code, model number, and parts list (with missing parts circled before calling.) Do not operate unit if damaged during shipping, handling or use. Damage may result in bursting and cause injury or property damage. Please read and save these instructions. Read carefully before attempting to assemble, install,

© 2008 IN614205AV 11/08 Oilless Compre s s o r s General Safety I n f o rmation ( C o n t i n u e d ) 6 . Do not stand on or use the pump or unit as a handhold. 7 . Before each use, inspect compressed air system and electrical components for signs of damage, deterioration, weakness or leakage. Repair or replace defective items before using. 8. Check all fasteners at frequent intervals for proper tightness. Motors, electrical equipment and controls can cause electrical arcs that will ignite a fla

Refer to motor name plate for electrical ratings and specifications. 3. The line wire is the proper size and that no other equipment is operated from the same line. The chart gives minimum recommended wire sizes for compressor installations. MiniMuM pipe Size for CoMpreSSed Air line CfM length of piping System 25 feet 50 feet 100 feet 250 feet 10 20 40 60 100 1/2 inch 3/4 inch 3/4 inch 3/4 inch 1 inch 1/2 inch 3/4 inch 1 inch 1 inch 1 inch 3/4 inch 3/4 inch 1 inch 1 inch 1 inch 3/4 inch 1 inch 1

Replace pressure switch 8. Replace pump / motor assembly Thermal overload 1. Lack of proper ventilation/room 1. Move compressor to a clean,well ventilated area where protector cuts out temperature too high temperature will not exceed 100°F. repeatedly 2. Decrease usage or purchase unit with higher air delivery 2. Excessive air usage, compressor too small (SCFM) Tank pressure drops when 1. Open tank drain valve 1. Close tank drain valve compressor shuts off 2. Loose connections (fittings, tubing,

Overheating, short circuiting and fire damage will result from inadequate wiring, etc. Operation Definition of Terms ON / OFF Switch ( I / O ) - Push switch to the ON ( I ) position to turn compressor on. Push switch to the OFF ( O ) position to turn compressor off. This switch should be in the OFF ( O ) position when connecting / disconnecting power cord from electrical outlet or when changing tools. Pressure Switch (located internally)- When the compressor is turned ON, this switch will shut c

Save this manual. Copyright© 1999 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. For technical questions or replacemen