clean, soft cloth. Not required, permanently lubricated. 10 TROUBLESHOOTING WARNING Never service heater while it is plugged in, operating, or hot. Severe burns and electrical shock can occur. Only a qualified service person should service and repair heater. OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Motor does not start when heater is plugged in and thermostat setting is higher than surrounding air temperature. 1. No power or low voltage at heater due to: A) Damaged power cord or extension cord B)

2. Remove side cover. 3. Pull upper fuel line off fuel filter neck. 4. Carefully pry bushing and fuel filter out of fuel tank. 5. Wash fuel filter with clean fuel and replace in tank. 6. Attach upper fuel line to fuel filter neck. 7. Replace side cover (see Figure 9). Fuel Filter Side Cover Upper Fuel Line Figure 9 - Fuel Filter Removal IGNITOR (RJ45) 1. Remove upper shell and fan guard (see Upper Shell Removal, page 8). 2. Remove fan (see Fan, page 8). 3. Remove side cover screws with a 5/16" n

Check circuit breaker in electrical panel is plugged in and switched ON WARNING: High voltage! 2. Bad electrical connection between mo-2. Check all electrical connections. See tor and ignition control assembly or ig-Wiring Diagrams, page 12 nition assembly and power cord 3. Binding pump rotor 3. If fan does not turn freely, see Pump Rotor, page 11 4. Defective ignition control assembly 4. Replace ignition control assembly 5. Defective motor 5. Replace motor 6. Defective ON/OFF switch 6. Replace

Allow motor to reach full speed. 4. Adjust pressure. Turn relief valve to right to increase pressure. Turn relief valve to left to decrease pressure. See specifications at right for correct pressure for each model. 5. Remove pressure gauge. Replace pressure gauge plug in filter end cover. (30/70,000 BTU/Hr Models Shown) Relief Valve Fan Guard (90,000 BTU/Hr Model Shown) Nozzle (30,000 BTU/Hr Model) 1. Remove upper shell (see page 10). 2. Remove fan (see page 19). 3. Remove fuel and air line hose

Pump Rotor, page 18. 9 10 099800 150 SHELL REMOVAL EA/EB Euro PV 020 Upper Shell Fan Guard Figure 12 - Fuel Filter Removal, 30/70,000 BTU/Hr Models Figure 11 - Upper Shell Removal, 150,000 BTU/Hr Model Figure 9 - Upper Shell Removal, 30/70,000 BTU/Hr Models Figure 10 - Upper Shell Removal, 90,000 BTU/Hr Model Upper Shell Fan Guard Fuel Filter Side Cover Fuel Line Fuel Filter (30/70,000 BTU/Hr Models) 1. Remove side cover screws using 5/16" nut-driver. 2. Remove side cover. 3. Pull rubber fuel li

29 ACCESSORIES Purchase accessories from your local dealer. 30 099800 AIR GAUGE KIT - HA1180 For all models. Special tool to check pump pressure. HEAVY DUTY WHEELS AND HANDLE KIT - HA1202 For heavy duty applications. Makes your heater even more portable and convenient. For 30/70,000 BTU/Hr models. STANDARD WHEELS AND HANDLE KIT - HA1206 Makes heater even more portable and convenient. Easy to assemble. For 30/70,000 BTU/Hr models. NOTES 31 WARRANTY AND REPAIR SERVICE CERTIFICATE OF GENERAL EQUIPM

Follow all ventilation and safety information. 2. Fill fuel tank with kerosene or No. 1 fuel oil. 3. Attach fuel cap. 4. Plug power cord of heater into standard 230 volt/50 hertz, grounded (earthed) outlet. Use an extension cord if needed. Use only a three-wire, grounded (earthed) extension cord. Extension Cord Wire Size Requirements Up to 30.5 meters long, use 16 AWG (1.0 mm2) conductor 30.6 to 61 meters long, use 14 AWG (1.5 mm2) conductor Heater will start when power cord is plugged into outl

10. Discard old motor. 11. Attach motor to motor mount with two nuts. Tighten nuts firmly. 12. Replace fan on motor shaft. Make sure set screw contacts flat surface on motor shaft. 13. Tighten set screw firmly (40-50 inch-pounds). 14. Carefully route motor wires through hole in shell (see Figure 7). Place motor, motor mount, and fan guard into rear of heater shell. 15. Insert screws through heater shell and into motor mount. Tighten screws firmly. 16. Turn heater on its side to access opening in

Release the control knob. 9. When burner remains lit, set heater at the desired heat level by turning the control valve counterclockwise. If burner goes out, turn off gas. Turn control knob fully clockwise to the lowest position. Check fuel supply. If adequate fuel is available, restart heater beginning at step 1. TO STOP HEATER 1. Tightly close propane supply valve on propane tank(s). 2. Wait a few seconds. Heater will burn gas left in supply hoses. 3. Turn control knob to the OFF position. 4.

(1.8 m), Sides: 2 ft. (60 cm), Top: 6 ft. (1.8 m), Rear: 2 ft. (60 cm). WARNING: Fire, burn, inhalation and explosion hazard. Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the heater as recommended by the instructions. Never use the heater in spaces which do or may contain volatile or airborne combustibles or productssuch asgasoline, solvents, paint thinner, dust particles or unknown chemicals. WARNING: Not for home or recreational vehicle use