and who will – connect the blue wire to the terminal marked with the letter comply with the l.E.E. and local regulations. N or coloured black; The wires in the mains lead are coloured in accordance with the – connect the brown wire to the terminal marked with the let- following code: ter L or coloured red. Green & Yellow = Earth Blue = Neutral . It is possible to connect the appliance directly to the mains Brown = Live. supply by means of a heavy duty switch with 3 mm minimum distance between th

omelettes 9 Fast frying steaks 5 for the zone required. The zone indicator will switch on to confirm the zone is active. Touch so the zone display shows 9. Touch again to set the required power level. The zone display will alternate between the required power level and A until the booster is complete, then it will show the required power level. Cooking zone power level 1 2 3 4 5 6 7 8 9 Fast heating time 1 min. 22 sec. 2 min. 44 sec. 4 min. 6 sec. 5 min. 28 sec. 6 min. 50 sec. 1 min. 22 sec. 2 m

• Keep children away from the appliance when in use. • Never put cooking foil or plastic materials on the ceramic surface when the hob is hot. These materials could melt and cause damage to the hob. • Never use the hob top for storage. • Pan handles should never stand out beyond the edge of the worktop. This will ensure children cannot reach them. • Do not use pans with rough bases (e.g. cast iron) as these may scratch the hob surface. • Do not switch on the zones without cookware in place. • Do

Gas connection GB Cat: II 2H3+ The gas supply must use the nearest gas inlet pipe which is located at the left or the right hand side at the rear of the appliance (figs. 35, 37). The hose should also be connected in such away that it does not touch the floor. To screw the connecting tube operate with two spanners (fig. 36). The unused end inlet pipe must be closed with the plug interposing the gasket. After connecting to the mains, check that the coupling are correctly sealed, using soapy soluti

Make sure that electrical cords connecting other appliance do not come into contact with the hob top. Before disposing of an unwanted appliance, it is recommended that it is made inoperative and that all potentially hazardous parts are removed. Using your hob HVC60 Zones: 1. Front left 1.2 kW 140 mm 2. Rear left 2.3 kW 210 mm 3. Rear right 0.75/2.2 kW 120/210 mm dual 4. Front right 1.2 kW 140 mm Control panel: 5. Front left zone control 6. Rear left zone control 7. Rear right zone control 8. Fro

RV 900 .. mod. RV 1000 .. Fig. 35b Conversion to Natural Gas or to LPG Conversion to Natural Gas or to LPG Injectors replacement of top burners Every cooker is provided with a set of injectors for the various types of gas. Injectors not supplied can be obtained from the After-Sales Service. Select the injectors to be replaced according to the table at page 47. The nozzle diameters, expressed in hundredths of a millimetre, are marked on the body of each injector. To replace the injectors proceed

Pleasekeepthebooklethandy.Youmaywishtorefertoitatalaterdate. CDA Important: This appliance is designed and manufactured solely for the cooking of domestic (household) food and is not suitable for any non domestic application and there- fore should not be used in a commercial environment. The appliance guarantee will be void if the appliance is used within a non domes- tic environment i.e. a semi commercial, commercial or communal environment. Contents Model RC 9301 .. Page Number Introduction .

Please note: You should avoid touching the zones when the hob is in use, or when an H is showing on the zone display. In the event of a power cut, the residual heat indicators will illuminate after the power supply is restored. However, when there is no power supply to the hob the residual heat indicators will not work, so extra care must be taken. Temperature Limiter The hob is equipped with a temperature limiting sensor that adjusts the power output of the hob if the bottom of the cookware bec

Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Stainless steel can be effectively cleaned by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth. Over time with use, the stainless steel surface may discolour; this is normal and does not constitute a fault with this appliance. Proprietary stainless steel cleaners are available. We recommend the CDA E-Cloth available from the CDA Sales Team f

• Do not cover the grilling grid with aluminium-foil. • Do not use the oven tray for roasting. • Do not place hot enamel parts in water. Leave them to cool first. • Do not allow vinegar, coffee, milk, saltwater, lemon or tomato juice to remain in contact with enamel parts (inside the oven and on the oven tray). • Do not use abrasive cleaners or powders that will scratch the surface of the stainless steel and the enamel. • Do not attempt to repair the internal workings of your cooker. • Do remove