4 •_ /,_ Replacing the Halogen Oven Light The oven licjhfs will automatically turn ON when the oven door is opened. The oven licjhfs may also be manually operated by pressing the _ pad. The oven light bulb is covered with a glass shield. The glass shield can be removed to be cleaned manually or to change oven light. THIS GLASS SHIELD MUST BE IN PLACE WHENEVER THE OVEN IS IN USE. To replace the light bulb: BE SURE THE OVEN IS COOL. l. Turn the power off at the main source. 2. Wear a leather-faced

Do not use thin aluminum cooking utensils or allow aluminum foil to touch the ceramic cooktop under ANY circumstances. • Aluminum utensils -The melting point of aluminum is much lower than that of other metals. Care must be taken when aluminum pots or pans are used on the ceramic cooktop. If allowed to boil dry, not only will the utensil be destroyed, but it may fuse to, break or mark the ceramic glass surface, permanently damaging the ceramic cooktop surface. Changing Oven Lights The oven light

Be sure the clock is set for the correct time of day. Fig. 1 2. Arrange interior oven rack(s) and place the food in the oven. 3. Press _, "---o,,will appear in the display (Fig. 1). G Fig. 2 GGG "350 °'' will appear in the display. 5. Press _. "BAKE" and "350 °'' will appear in the display (See Fig. 3). Fig. 3 OVEN COOK 6. Press OVENCOOK . "TIMED" will flash; "BAKE", "0:00" and "350 °'' will appear in the display (Fig.4). 7. Enter the desired baking time by pressing ____@. (_(_ Fig. 4 "TIMED" wi

Setting Convection Bake --Multiple rack baking. --No special pans or bakeware needed. Setting Convection Bake Air The CONVECTION BAKE _ pad controls the Convection Bake feature. during Use the Convection Bake feature when cooking speed is desired. The oven Convection can be programmed for Convecfion baking at any temperature between 300 ° F Figure 1 Bake (149°C)to 550°F(288°C). Convection baking uses a fan to circulate the oven's heat evenly and 1stPositionPosition nd RackRackcontinuously within

Only flat-bottom cookware should be used. The type and size of cookware, the number of surface elements in use and their settings, are all factors that will affect the amount of heat that will spread to Figure 1 areas beyond the surface elements. The areas surrounding the elements may become hot enough to cause burns. About the Radiant Surface Elements The element temperature rises gradually and evenly. As the temperature rises, the element will glow red. To maintain the selected setting, the el

entered except the Use to turn the Bake feature Bake Oven Lockout,time of the Meats, oven lights on (See page 26). feature, Cakes and day and minute timer. Press CLEAR/OFF to and off (See (See page Breads cooking page 34). 21). feature, (See stop cooking. page 25). Minimum All of the features listed have minimum and maximum time or temperature settings that may be entered into the control. An ENTRY acceptance beep will sound each and time a control pad is touched (the Oven Lockout pad is delayed

cooktop surface utensils can cause scratches, Be sure cooktop surface and bottoms of utensils are clean before placing on cooktop, Small scratches do not affect cooking and will become less visible with time, Cleaning materials not recommended for ceramic-glass cooktop have been used, See "Cooktop Cleaning & Maintenance" in the GeneraJ Care & Cleaning section, Cookware with rough bottoms were used, Use smooth, fiat-bottomed cookware ONLY (See Figs, 20 & 21 ), Brown streaks or specks on ceramic B

When you have finished, replace the protection and lock it in place with screw “S”. Before using the oven, make sure the sliding protection “A” is fastened in the correct position. Storage recess below the oven (only a few models) Below the oven a recess can be used to contain cooking pans and cooker accessories. Moreover, during oven operation, it may be used to keep food warm.To open the storage is necessary turn it downwards. Caution: this storage recess must not be used to store inflamma

plate ofthe appliance. 3 This owner’s manual is for a class 1 appliance (insulated) or class 2, subclass 1 appliances (installed between two cabinets. 4 Betoreusing yourappience, neadtheinstructiorsinthisowner'smanual carefuly sinceitpravides all the information you need to ensure safe installation, use and maintenance. Always keep this owner's manual close to hand since you may need to referto tin the future. 5 Whenyouhaveremovedthepacking, checkthattheapplianceisnotdamaged. Ifyou have any d

4. When cooking has completed, turn the surface control knob to OFF before removing the cookware. Note: The HE message will appear inthe display after turning the Figure 3 control knob to OFF if the cooktop is still hot and remain on until the heating surface area has cooled sufficiently. The message may remain on even though the controls are turned OFF. Note: See Table on previous page for recommended control settings. Radiant surface elements may appear to be cooled after they have been turned