Product Registration Fill out the enclosed warranty registration form and return to LAMAR Health, Fitness & Sports, LLC within 30 days of product purchase. You can also register your product online. Along with product registration, keep copies of all product information for your personal records. Product Information Model:_______________________ Purchase Date:_____________ Serial Number:___________________________________________ Contact Information: Address: LAMAR Health, Fitness & Sports, LLC

Paint/finish, components attached to the bicycle/ frameset such as front forks, wheels, drive train, brakes, seatpost, handlebar and stem or any suspension related parts or components are covered under the limited one (1) year warranty. This warranty is void if the bicycle or frameset was not purchased new from or not properly assembled by an authorized Specialized dealer. LIMITED ONE (1) YEAR WARRANTY ON COMPLETE BICYCLE Subject to the following limitations, terms and conditions, Specialized wa

Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. 4 P/N 211689C 05/03 Get to know the basic parts of your basketball system..... FRONT BACK TOP POLE MIDDLE POLE FRONT COVER RIM BOTTOM POLE BASE STRUTS ELEVATOR ASSEMBLY BACKBOARD WHEEL CARRIAGE ASSEMBLY 5 05/03 P/N 211689C Item Qty Part No Descript

Label is shown on page 1 If technical assistance is required, contact Huffy Sports. Adult supervision is recommended when adjusting Most injuries are caused by misuse and/or not following Use caution when using this system. For more information on assembly, placement, maintenance, visit The American Basketball The NBA and individual NBA copyrighted designs, and/or Properties, Inc. and the respective written consent of NBA Toll-Free 1-800-558-For Canada: 1-800-284-For Europe: 00 800 555 (Sweden:

10 14 20 7 1421 12 10 THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING REAR VIEWIMPORTANT! Do not over tighten. 9 12/02 P/N 211446D Rotate jack handle clockwise to raise H-frame (13) to approximately 7’ (2.1 m) from ground. Secure crank jack (20) to jack brackets (17 &18) as shown. NOTE: Some adjustment will be necessary to align the lower crank jack bushing to jack brackets (17 & 18). 15. THREE PER

x 1.19 Long 56 4* 203257 Zip Tie 57 1 203255 Front Cover * You may have extra parts with this model. P/N 211447 04/01 4 printed on recycled paper ENGLISH INSTRUCTIONS use washers here on spring return style rim. NOTE B: Mounting nuts and IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF bolts supplied with rim hardware. THIS OWNERS MANUAL 20. 1. Remove all contents from underside of tank. Keep tank (1) bottom side 21. up. 22. 2. Insert axle rod (2) through wheel (3), as shown. Secure wheel a

Test fit large bolts into large holes of elevator tubes, backboard brackets and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. AVANT DE COMMENCER ! Pour garantir l'utilisation optimale du panneau, les composants du systeme elevateur et la visserie doivent etre bien ajustes (serres). A titre d'essai, inserez les gros boulons dans les gros trous des tubes du systeme elevateur, des supports du panneau et des plaques triangulaires. Bas

Wir empfehlen, die Korbwand an einem festen Material (Stahl) hinter dem Korbrandbereich anzubringen. Recomendamos montar el respaldo en un material solido (acero) detras del area del borde. REMARQUE: HINWEIS: NOTA: Utilisez les composants du systeme elevateur existants. Die bereits vorhandenen Komponenten des Verlangerungssystems verwenden. Use los componentes existentes del elevador. REMARQUE: HINWEIS: NOTA: FIXATION SUR SYSTEME ELEVATEUR / MONTAGE AN VERLANGERUNGSSYSTEMEN / MONTAJES PARA EL EL

x1.5 Long * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. WARRANTY CARD: Please remember to complete your product registration form either on-line at: or mail-in the enclosed postcard. HARDWARE IDENTIFIER Item #8 (1) Item #2 (2) Item #10 (1) Item #12 (1) Item #13 (7) * You may have extra parts with this model. HARDWARE IDENTIFIER (CONTINUED) Item #9 (1) Item #7 (1) 2 P/N 211955C 04/03 3 04/03 P/N 211955C Item #14 (1) Item #15 (2) Item #16 (9) Item #18 (2) Item #19 (4) Item #20 (4) Item #21 (4) Item

voneinander getrennt werden. HINWEIS: Die Stangenteile mussen Die Stange auf einen Sagebock legen. Die Korbwandbaugruppe wie einander um mindestens 9 cm (3 . Zoll) uberlappen. gezeigt am oberen Stangenteil (4) befestigen. 5. Die Stange (7) durch die Locher im unteren Stangenteil (6) und die Dann die Stangenkappe (37) aufsetzen. HINWEIS: Diese Arbeit Einschraubose (8) stecken. sollte von zwei Personen ausgefuhrt werden. Vorsicht: Die 6. Den Stangenaufbau wie gezeigt in die Tankbaugruppe stecken.