Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
x1.5 Long * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. WARRANTY CARD: Please remember to complete your product registration form either on-line at: or mail-in the enclosed postcard. HARDWARE IDENTIFIER Item #8 (1) Item #2 (2) Item #10 (1) Item #12 (1) Item #13 (7) * You may have extra parts with this model. HARDWARE IDENTIFIER (CONTINUED) Item #9 (1) Item #7 (1) 2 P/N 211955C 04/03 3 04/03 P/N 211955C Item #14 (1) Item #15 (2) Item #16 (9) Item #18 (2) Item #19 (4) Item #20 (4) Item #21 (4) Item #23 (2) Item #22 (2) Item #25 (1) Item #30 (2) Item #31 (1) Item #36 (2) Item #39 (7) HARDWARE IDENTIFIER (CONTINUED) Item #47 (6) Item #48 (1) Item #55 (4)* * You may have extra parts with this model. Item #44 (2) Item #57 (4) Item #38 (4) Item #50 (12) BEFORE YOU START! INSTRUCTIONS IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL 1. Remove all contents from underside of tank. Keep tank (1) bottom side up. 2. Insert axle rod (2) through wheel (3), as shown. Secure wheel assembly to tank (1) by tapping wheel downward with hammer, snapping it into position. Repeat for opposite side, then carefully, turn tank (1) over. 3. Mark pole sections with tape as shown. 4. IMPORTANT! Center alignment slot of middle pole section (5) in a lower hole of top pole section (4) as shown. While maintaining alignment, bounce pole top (4) and middle section (5) together as shown until they no longer move toward taped reference mark. Upright assembly. NOTE: Pole sections should have a 3-1/2” (9 cm) overlap minimum. 5. IMPORTANT! Center alignment slot of lower pole section (6) in a lower hole of middle pole section (5) as in step 4. While maintaining alignment, bounce assembly and lower section (6) together as shown until they no longer move toward taped reference mark. NOTE: Pole sections should have a 3-1/2” (9 cm) overlap minimum. 6. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 7. Insert pole assembly into tank assembly as shown. 8. Carefully place unit on its side. Secure pole bottom (6) to tank with anchor strap (52), washers (9 & 13) and nut (10) as shown. Upright unit. NOTE: Keep unnecessary pressure off of the pole assembly when in this position. Two people recommended for this procedure. IMPORTANT! DO NOT over tighten. 9. Secure strut tubes (11) to bottom pole section (6) as shown. 10. 11. 12. 13. 14. 15. 16. 17. (34) carefully ream out paint from holes if necessary. IMPORTANT! It is necessary for all parts to be installed for this mechanism to work safely and properly. 18. Assemble upper elevator tubes (43) to backboard brackets (34). 19. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (46). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy. 20. Install upper elevator tubes (43) to triangle plates (45) as shown. Install handle assembly to lower elevator tubes (40) using bolt (47), spacers (44), and nut (39) as shown. NOTE: Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. 21. Insert bolt (47) through left side upper elevator tube (43), then stretch spring (41) onto bolt (47). Insert bolt (47) through right side upper elevator tube (43) and secure with nut (39). WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS. 22. Roll completed assembly to desired position. Secure assembly to ground using anchor strap (52) and tie down stake (53). Fill tank with water (approx. 30 gallons (115 Liters)) or sand (approx. 255 lbs. (113 kg)) and snap cap (49) in place. IMPORTANT! Add two gallons (7.6 Liters) of non-toxic antifreeze in sub-freezing climates. WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY, MAY TIP OVER. 23. While holding handle, remove pin (26). WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT. 24. Move elevator up or down to desired height. 25. Replace pin (26) full length to lock system at desired height. 26. Apply height and transport label (54) to front of pole as shown. 27. Install front cover (35) onto struts (11) as shown. 28. Loop zip tie (56) around strut (11) and cover (35). Pull flat end of zip tie of To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test fit large bolts into large holes of elevator tubes, backboard brackets and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-FREE NUMBER FOR FREE REPLACEMENT: U.S. 1-800-558-5234; CANADA: 1-800-284-8339; 4 P/N 211955C 04/03 IMPORTANT! 1. 1. WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL 3 2 1 1 2. 3. 4 5 6 5 ...