Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Mitsubishi Electronics Dateigröße: 2.33 mb Dateiname: Unterrichtssprache:

Available for 480i, 480p and digital standard 4:3 signals only. Caution should be observed when using the Narrow format due to the stationary gray side bars. Please see guidelines concerning stationary images, page 70. 64 65 Programming the Remote Control to Control NetCommand™ A/V Products NetCommand™ CODE to ENTER To Program the Remote to Control TV Control and NetCommand™ 935 NetCommand™ A/V Products: Devices: (See NetCommand Supported Devices, for the list of A/V products supported by the NetCommand™ System.) 1. Move the slide switch at the top of the remote to the TV layer. 2. Press and hold the POWER button on the remote control. Figure 1. Programming the TV remote to control your NetCommand™ A/V devices. 3. Enter the three digit code of 935, and then release the POWER button on the remote control. 4. The remote control is now programmed to send NetCommand™ signals to the TV so the TV can control the IEEE 1394 devices and selected older NetCommand™ supported IR devices. See the NetCommand™ guide for details. 66 Programming the Remote Control to Control Non-NetCommand™ AV Products To Program the Remote to Control Other Brands of Audio and Video Products: (Figures 1-5) 1. Move the slide switch at the top of the remote to the product you want to control. 2. Press and hold the POWER button on the remote control. 3. Enter the first three digit code listed for your equipment, and then release the POWER button on the remote control. 4. Point the remote control at the equipment and press the POWER button. If the equipment responds, the remote control is properly programmed to operate the equipment. If the equipment does not respond, repeat steps 2-4 with the next three digit code listed in step 3 for your equipment. Figure 2. Programming the remote to control your satellite receiver. Figure 1. Programming the remote to control your cable box. Figure 3. Programming the remote to control your VCR. 67 IMPORTANTIf you cannot turn the cable box ON by pressing POWER, try pressing CHANNEL or the number buttons. Programming the Remote Control to Control Non-NetCommand™ A/V Products After entering the correct codes in each position of the remote control, use the slide switch to select which product will respond when an operational button is pressed. If the TV position has not been programmed to control NetCommand™ and you enter a code from the A/V Receiver chart while the slide switch is set to TV, the volume and mute functions change to match the A/V receiver. This is useful when using an A/V receiver with the TV all the time. In all other cases, only one of the below devices is allowed for each slide switch position. TV position (when the remote has not been programmed to operate NetCommand™): TV A/V receiver (volume and mute only) Cable/DBS/DTV position: Cable box Satellite receiver DTV receiver VCR position: VCR DVD LD Player DVD position: DVD LD Player Cable box VCR Audio position: A/V receiver Cable box Mitsubishi CD player [If you have a Mitsubishi A/V receiver, the audio position may be used in conjunction with selected Mitsubishi CD players. Your audio position must be programmed to 010 ]. Figure 4. Programming the remote to control your DVD/ LDP. Figure 5. Programming the remote to control your A/V receiver. IMPORTANT If the remote control has not been programmed to operate NetCommand™ and slide switch is set to TV when you enter an A/V receiver code, VOLUME and MUTE will control the A/V receiver rather than the TV. To return volume and mute control to the TV, set the slide switch to TV, press and hold POWER and enter 000. IMPORTANT Some manufacturers may change their products, or they may use more than one remote control system. If this is the case, your remote control may not be able to operate your VCR, DVD, cable box, satellite receiver, or A/V receiver. 68 Remote Control Functions: Special Functions When your remote control has been Programmed to operate another manufacturer’s product, the function performed on each layer can vary. The most common functions are: ......... ....... ......... ........... ............. ............. ..... ....... ............. ................... ....... ....... ... ................... ....... ................... ............. ......... ......... ..... ................. ................. ......... ......... ..... ....... ............. ........... ................................... ............. ............. ........... ..... ....... ............. ..... ....... ............. ..... ........... ............. ..... ....... ............. ......... ..... ....... ............. ..... ................. ......... ........... ....... ................... ..... ................. ........... ......... ................. ............. ....... ........... ............... ....... ..... ... ..... ....... ............. ................... ... ............. ....... ..... ................. ..... ..... ............. ....... ........... ............. ......... ....... ..... ..... ......... ........

Herunterladen

Geben Sie zwei Ziffern: