Stimmen - 5, Durchschnittliche Bewertung: 3.6 ( )

Hersteller: Harbor Freight Tools Dateigröße: 759.27 kb Dateiname: Unterrichtssprache:

The operator must understand that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SAVE THESE INSTRUCTIONS ASSEMBLY AND OPERATING INSTRUCTIONS NOTE: For additional references to the parts listed in the following pages, refer to the Assembly Diagram on page 9. To Attach A Quick Connector: 1. WARNING! Prior to performing any assembly and/or adjustment procedures, make sure the air supply hose (not included) is disconnected from the Die Grinder. SKU 92144/92007 For technical questions, please call 1-800-444-3353 PAGE 5 2. Prior to use, the Die Grinder requires the attachment of a Quick Connector (34) into its Air Inlet (1). To do so, wrap approximately 3” of pipe thread sealer tape (not included) around the male threads of a Quick Connector. Then, firmly tighten the Quick Connector into the Air Inlet. (See Figure A.) RECOMMENDED COMPRESSED AIR SYSTEM QUICK CONNECTOR (34) AIR INLET (1) AIR HOSE (NOT INCLUDED) QUICK CONNECTOR TO OILER (NOT INCLUDED) QUICK COUPLER (NOT INCLUDED) REGULATOR (NOT INCLUDED) AIR HOSE (NOT INCLUDED) COMPRESSOR (NOT INCLUDED) FIGURE A FILTER (NOT INCLUDED) OILER (NOT INCLUDED) To Operate The Die Grinder: 1. WARNING! Always wear ANSI approved safety glasses, a full face shield, and hearing protection when operating the Die Grinder. 2. Use the two Wrenches (24) provided to loosen the Collet Nut (25). (See Figure B, next page.) 3. Insert the Collet (26) into the Spindle (27). (See Figure B.) 4. Insert the 1/4” diameter shank of a Grinding Drum (not included) fully into the Collet (26). Then, firmly re-tighten the Collet Nut (25) to lock both the Collet and Grinding Drum in place. (See Figure B.) SKU 92144/92007 For technical questions, please call 1-800-444-3353 PAGE 6 COLLET (26) WRENCH (24) COLLET NUT (25) GRINDING DRUM (NOT INCLUDED) WRENCH (24) SPINDLE (27) FIGURE B 5. Connect the air supply hose to the Quick Connector (34) on the Die Grinder. Turn on the air compressor, and set its regulator to the recommended 90 PSI for the Die Grinder. (See Figure A.) 6. In order to keep the air supply hose out of the way, hang it over your shoulder. 7. IMPORTANT! Grip the Die Grinder firmly with both hands. 8. Trip the Safety (8) with your finger. Then slowly apply hand pressure to the Trigger (4) until the desired speed is obtained. NOTE: The Die Grinder always turns the Grinding Drum clockwise. (See Figure C.) TRIGGER (4) SAFETY (8) FIGURE C 9. With a firm grip on the Die Grinder, lightly apply the Grinding Drum to the workpiece, slowly and steadily moving the Grinding Drum to the right and left until you have achieved the desired appearance (finish) on the workpiece. 10. Once the work is completed, release hand pressure on the Trigger (4). The Safety (8) will automatically return to its locked position to prevent the Trigger from accidentally being activated. (See Figure C.) 11. Turn off the air compressor. Trip the Safety (8) with your finger, and slowly squeeze the Trigger (4) to release any remaining air pressure from the Die Grinder. Then, disconnect the air hose from the tool. (See Figure A.) SKU 92144/92007 For technical questions, please call 1-800-444-3353 PAGE 7 12. Remove the Grinding Drum from the Die Grinder. Then, store the tool in a clean, dry location out of reach of children. INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Always make sure the Trigger (4) is in its “OFF” position, and disconnect the Die Grinder from its compressed air supply before performing any inspection, adjustments, maintenance, or cleaning. 2. Before each use, inspect the general condition of the Die Grinder. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged air hose, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. 3. Daily: With a clean cloth, remove all dirt, oil, and grease from the Die Grinder. If necessary, you may use a mild detergent. Do not use solvents, as damage to the Die Grinder may occur. Do not immerse the Die Grinder in any liquids. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 92144/92007 For technical questions, please call 1...

Herunterladen

Geben Sie zwei Ziffern: