File these instructions with the owner or maintenance department. P.O. Box 309, Menomonee Falls, WI 53052-0309 215-1384Rev.A;EN01-819 TEL. 1-800-BRADLEY FAX (262) 251-5817 Page1of4 Express® LavatorySystemMG-SeriesExtension MG-EXT InstallationInstructions Pre-Installation Information Check Contents Separate all parts from the packaging and check each part with the drawing below. Make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not attemp

3 Assembly of Components ................. 4 PartsLis ............................ . 4 IMPORTANT This equipment should be inspected, tested, and recorded weekly to maintainproper operation. Main water supply to the eye wash should be “ON” at all times. This installation manual and parts list should be filed by the building owner’s maintenance department. 215-148AE Ref. G; EN 98-579 Page 1 of 4 PO. Box 309, Menomonee Falls, WI USA 53052-0309 PHONE (414) 251-6000 FAX (414) 251-5617 http:/lBradley

FRAME (4) 3/8" BOLT AND WASHER Figure 4 Figure 2 1-1/2" NPT DRAIN STUB-OUT 1/2" NPT HOT AND COLD SUPPLIES OR TEMPERED SUPPLY STUB-OUTS Figure 3 PANEL FRAME (8) TORX-HEAD SCREW SCUFF PANEL (do not remove) SCUFF PANEL (do not remove) Installation Instructions continue . . . Bradley Corporation • 215-1244 Rev. D; EN 08-805 4/24/08 Express® Lavatory System SS-Series SS-2/AST/STD, SS-2/AST/JUV Installation - Obsolete Installation Instructions continued . . . Step 3: Installing bowl assembly IMPORTANT

IMPORTANT Read this entire installation manual to ensure proper installation, thenfile these instructions with the owner or maintenance department. Flush all the water supply linesbefore making connections. Wall anchors used must have a minimum pull-out rating of 1,000lbs. Product warranties may be foundunder "Product Information" on our web site at Table of Contents Pre-Installation Information . . . . . . . . . . . . . . . .2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

When mounted at 34" rim height, the Express® meets ADA, ANSI and UFAS requirements for barrier-free clearances, reaches and controls. Always check local codes and ordinances for compliance. Barrier-free and ADA compliant - juvenile height mounting The SS-2/IR/JUV Express® Lavatory System is compliant with Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities: Building Elements Designed for Children's Use; Final Rule. Infrared sensor and solenoid Each sprayhe

. . Bradley Corporation • 215-1243 Rev. E; EN 08-805 4/24/08 Express® Lavatory System SS-Series SS-2/IR/STD, SS-2/IR/JUV Installation - Obsolete Installation Instructions continued . . . Step 2: Mounting frame to wall 1. Remove the eight Torx-head screws securing the panel to the frame, and remove the panel (see Figure 3). Note: Scuff panel does not need to be removed. 2. Position the frame against the wall, ensuring that it is level. If necessary, insert shims under the frame until level. Note:

Do not use pipe dope on faucet and supply connections. Possible solenoid contamination could occur and will void any warranty. Teflon tape is the recommended sealant. Use plumber’s putty only to seal the faucet to the deck. The installation site should have access to an electrical box with 120 volt AC, 60 Hz cycle for input to a transformer. When installing the transformer, the electrical box should be located within six feet of the sink. The DC faucets are powered by four “AA” factory-installed

2 1 2 When installing the transformer, make sure the electrical box is located within 6' of the sink. Install the baseplate and mount the electronic box to the desired wall location. The baseplate must be mounted either level with or above the solenoid valve, and within 12" of the solenoid valve. Make sure the transformer wires (1) are positioned in the baseplate channel (2) before mounting the unit. NOTE: When positioning baseplate, make sure there is enough room for drip loops in final install

This will continue for 8 minutes and then stop. Proceed to Faucet Operation, page 6. Bradley Corporation •215-1559 Rev. A; EN 04-216A 9/23/04 Aerada 1000 Series Gooseneck Faucet Installation Instructions Faucet Operation Operating Modes • Normal Motion Detecting Mode: water flows within 1/4 second after activating sensor (i.e., putting hands in front of collar) and continues to stay on as long as motion is detected. Maximum time is 45 seconds (factory default setting). • Scrub Mode: water contin

The following chart provides details concerning the number of beeps and possible errors associated with them . 1 Beep: Indicates low battery. 2 Beeps: Calibration out of range (environment too reflective). 3 Beeps: Room infrared level out of range; too much sunlight, heat lamp present, etc. 4 Beeps: Solenoid short circuit. 5 Beeps: Solenoid unplugged or loose/broken solenoid connection. Refer to Troubleshooting Chart below and on page 8 for further troubleshooting information. Problem Check Poss