Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Delta Dateigröße: 869.21 kb Dateiname: Unterrichtssprache:

Fig. 12. 3. To remove FRONT PANEL (2) insert WIRE KEY (5) (supplied) into the two holes located at the bottom of the FRONT PANEL (2). Push the WIRE KEY (5) up until it releases the bottom clips. Pull the bottom edge away and lift the FRONT PANEL (2) off. Fig. 12. 9 INSTALL FRONT PANEL; Fig. 12 PUSH TO SNAP PANEL INTO PLACE 5 2 TOP 5 7 BLACK & RED WIRES TOP 1 2 3 4 6 TOP 3 10 M968550 REV. 1.6 10 CONNECT OVERRIDE HOSES, AC & DC POWER; Fig. 13 1. Push the BLACK HOSE (1) into the BOTTOM HOSE CONNECTOR (2) and the other end into the back of the OVERRIDE SWITCH (3). 2. Push the BLUE HOSE (4) into the TOP HOSE CONNECTOR (5) on the valve and the other end into the BOTTOM CONNECTOR (6) on the OVERRIDE SWITCH (3). 11 CONNECT SOLENOID WIRING AND POWER SUPPLY; Fig. 14 1. Push the RED WIRE CONNECTOR (1) onto the SOLENOID PIN (2) with Red Stripe. Push the BLACK WIRE CONNECTOR (3) onto the other SOLENOID PIN (4). Push the wire connectors all the way down. 2. Code approved Electrical Outlet provided by others, (120V 50/60 Hz). 3. Plug AC POWER SUPPLY (5) into Outlet. 1 4 2 5 5 6 BLUE HOSE BLACK HOSE Fig. 13 Fig. 14 3 RED WIRE RED STRIPE BLACK WIRE ELECTRICAL OUTLET 1 3 2 4 M968550 REV. 1.6 8 FOR AC-VERSION (MULTI HOOK-UP); Fig. 15, 15a Unit #1 Unit #1 Unit #2 Unit #3 1. Remove the COVER SCREWS (1) and COVER (2) from each ELECTRICAL BOX (3). 2. See AC Version Electrical Hook-up for Unit #1 of the Multi hook-up. 3. Install SENSOR WIRE GROMMET (4) and FLUSH VALVE SENSOR WIRE (5) into the COVER (2) of each unit. Insert the flush valve sensor wire connector into the CENTER CIRCUIT BOARD RECEPTOR (6) on each unit. Fig. 15a. 4. Remove the SPLIT PLUG (7a) from the SENSOR WIRE GROMMET (7) on the left side of each ELECTRICAL BOX (3). 5. Take the 10 ft. EXTENSION WIRE (8) from Unit #2 and insert one end of the EXTENSION WIRE CONNECTOR (9) through the SENSOR WIRE GROMMET (7) on left side of Unit #1. Insert EXTENSION WIRE (8) into SPLIT PLUG (7a). Push SPLIT PLUG (7a) into SENSOR WIRE GROMMET (7) to seal. Insert EXTENSION WIRE CONNECTOR (9) into LOWER CIRCUIT BOARD RECEPTOR (10). Fig. 15a. 6. Insert other end of EXTENSION WIRE (8) into SENSOR WIRE GROMMET (7) on left side of Unit #2. Insert that EXTENSION WIRE CONNECTOR (9) into the LOWER CIRCUIT BOARD RECEPTOR (10) of Unit #2. Fig. 15b. 7. On Unit #2 ELECTRICAL BOX (3) remove ROUND KNOCK-OUT (11) on the bottom of the box by pressing a flathead screwdriver into the center of the ROUND KNOCK-OUT (11). Fig 15b. 8. Insert additional SENSOR WIRE GROMMET (12) included with Unit #2 into the knock-out opening in the bottom of the ELECTRICAL BOX (3). Take the 10 FT. EXTENSION WIRE (8) from Unit #3 and insert one end into the SENSOR WIRE GROMMET (12) in the bottom of the ELECTRICAL BOX (3) of Unit #2. Insert EXTENSION WIRE CONNECTOR (9a) into TOP CIRCUIT BOARD RECEPTOR (13) on Unit #2 . Fig. 15b. 9. Insert the other end of the EXTENSION WIRE (8) from Unit #3 into the SENSOR WIRE GROMMET (7) o...

Herunterladen

Geben Sie zwei Ziffern: