Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: American Standard Dateigröße: 869.21 kb Dateiname: Unterrichtssprache:

3 1. Cut a 127x127mm (5"x 5") opening in finished wall for ELECTRICAL BOX (1) at the deminsion shown in Fig.3. 2. Rotate the 4 MOUNTING TABS (2) flat against the electrical box. Holding the MOUNTING TABS (2) in position install the ELECTRICAL BOX (1) into the opening. Make sure the MOUNTING TABS (2) are behind the wall. 3. Tighten the the 4 MOUNTING SCREWS (3) until the ELECTRICAL BOX (1) is almost secure in the wall. Before tighting fully rest a level at the top edge of the ELECTRICAL BOX (1) and make sure the box is level, then tighten fully. Fig. 3a. 4. *Cut a 2" hole for supply to fixture at deminsion shown. 2 INSTALL SWEAT SOLDER ADAPTER; Fig. 4 CAUTION Turn water supplies off before beginning Note: Control stop inlet is 1" IPS. For optional sweat connection, install Sweat Solder Adapter (1) (Supplied) for 1" copper pipe supply line. Fig. 4. 1. Clean the end of the supply pipe. Push the threaded ADAPTER (1) on until it is seated against the internal stop. Sweat the ADAPTER (1) to the pipe. 2. From behind the wall install the CONTROL STOP (2) to the water supply line with the outlet positioned as required. 3. Support piping as required. 3 FLUSH OUT SUPPLY LINES; Fig. 5 1. Open SUPPLY STOP (1). 3. Turn on water supply to flush line of any debris or sediment. 4. Close SUPPLY STOP (1) and turn off water supply line. Fig. 4 Fig. 3a Fig. 5 Fig.3 (TOP SPUD FIXTURE ILLUSTRATED) 1 3 2 2 1 1 *FOR HOLE LOCATION OF SUPPLY ON BACK INLET FIXTURES, REFER TO FIXTURE BEING INSTALLED FOR CORRECT HEIGHT FROM FINISHED FLOOR 127mm (5) 406mm (16 REF.) 127mm (5) TO P FILE EDGES CLEAN & SOLDER TO ADAPTER (1) 115mm-134mm (4-1/2 TO 5-1/4) CONTROL STOP DN 25mm (1" I.P.S.) CONTROL STOP OUTLET CLOCKWISE CLOSES CONTROL STOP COUNTER-CLOCKWISE OPENS CONTROL STOP TOP TO P 2 403 TO 441mm (15-7/8 MIN. TO 17-3/8 MAX.) 127mm (5 MAX.) M968550 REV. 1.6 3 44 INSTALL VACUUM BREAKER AND FLUSH CONNECTIONS; Fig. 6 1. Place the SPUD FLANGE (1) over the spud on the Fixture. Fig. 6. 2. Thread SPUD COUPLING NUT (2) onto Spud. Make sure SEAL WASHER (4) and FRICTION WASHER (3) are installed. Do not tighten fully. Fig. 6. 3. Remove the COUPLING NUTS (6, 6a) from the CHROME ELBOW (5). Make sure you have a TAPERED RUBBER WASHER (7), PLASTIC SUPPORT (8) and SQUARE SEAL WASHER (9). Fig. 6a. 4. Install the SQUARE SEAL WASHER (9) onto the PLASTIC SUPPORT (8) if not already installed. Insert the PLASTIC SUPPORT (8) into the DOWN TUBE (10). Slide the COUPLING NUT (6) onto the DOWN TUBE (10). Connect the COUPLING NUT (6) to the CHROME ELBOW (5) and tighten fully. Insert the DOWN TUBE (10) with CHROME ELBOW (5) into the SPUD COUPLING NUT (2) and push it down. Do not tighten fully. Fig. 6a. Note: If center line of ELBOW (5) cannot be adjusted to line up with hole in wall, then cut the DOWN TUBE (10) as required. 5. Measure and cut the HORIZONTAL TUBE (11) to length required. Important: Make sure that there is a minimum of 1-1/4" for engagement with elbow when ...

Herunterladen

Geben Sie zwei Ziffern: