Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the charger. Insert the cartridge fully into the port so that it rests on the charger port floor. 3. When the battery cartridge is inserted, the charging light color will flash in red color and charging will begin. 4. When the charging light goes out after about one hour, you may remove the fully charged battery cartridge. 5. After charging, unplug the

Release the switch trigger to stop. CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. ASSEMBLY 1. Lock-off lever 2. Switch trigger 1 2 3 1 2 3 Bolt 2. Flange 3. Diamond wheel 003526 Installing or removing diamond wheel To install the wheel, first loosen the bolt with the hex wrench and remove the bolt and the flange. Then mount the wheel, the flange and the bolt. The wheel should be mounted with the Makita name

To install the wheel, first loosen the bolt with the hex wrench and remove the bolt and the flange. Then mount the wheel, the flange and the bolt. The wheel should be mounted with the Makita name on the flange side. Press the blade stopper pin and insert it through the hole in the wheel so that the wheel cannot revolve. Use the hex wrench to tighten the bolt securely. To remove the wheel, follow the installation procedure in reverse. CAUTION: • When installing the wheel, be sure to tighten the b

Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the battery charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When the battery cartridge is inserted, the charging light will come on and charging will begin. The charging light will keep lighting up steadily during charging. When charging is completed, the charging light goes out. The charging time is approx.

round) arbor holes. Wheels that do not match the mounting hardware of the tool will run eccentrically, causing loss of control. 9. Never use damaged or incorrect wheel washers or bolts. The wheel washers and bolt were specially designed for your tool, for optimum performance and safety of operation. 10. Causes and Operator Prevention of Kickback: Kickback is a sudden reaction to a pinched, bound, or misaligned wheel, causing an uncontrolled tool to lift up and out of the work- piece toward the o

Importante: Leer cuidadosamente este manual de instrucciones antes de poner en marcha la maquina y observar estrictamente las normes de seguridad. Conservar este manual de instrucciones con cuidado. Brush Cutter Debroussailleuse Desbrozadora BCM2600 BCM3300 String Trimmer Taille-bordures Cortabordes BCM2310 BCM2310CA BCM2610 BCM2610CA BCM3310 BCM3310CA ENGLISH Thank you very much for purchasing MAKITA Brush Cutter/String Trimmer. We are pleased to recommend to you the MAKITA Brush Cutter/String

5 Put the cord ends temporarily into the notched (H) when winding being finished. Leave approximate 100 mm (4”) of the cord extended beyond the notch. 6 Place the spool into the cover. Remove the ends of the cord from the notches (H) and put them in the metal eyelets (I) on the cover. 7 Mount the spool ( cover-assembly ) in the housing so that the grooves and protrusions on the spool mach up with those in the housing ( C ). C A I B G E F D H Then push the cover firmly onto the housing to secure

Check the security of the cutting tool, the control lever for easy action and check for proper functioning of the control lever lock. - Rotation of the cutting tool during idling the engine is not allowed. Check with your dealer for adjustment. Check for clean and dry handles and test the function of the start/stop switch. - Start the Brush Cutter/String trimmer only in accordance with the instructions mentioned in this manual. Do not use any other methods for starting the engine. - Use the Brus