Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
To install the wheel, first loosen the bolt with the hex wrench and remove the bolt and the flange. Then mount the wheel, the flange and the bolt. The wheel should be mounted with the Makita name on the flange side. Press the blade stopper pin and insert it through the hole in the wheel so that the wheel cannot revolve. Use the hex wrench to tighten the bolt securely. To remove the wheel, follow the installation procedure in reverse. CAUTION: • When installing the wheel, be sure to tighten the bolt securely. • Use only the Makita hex wrench to install or remove the wheel. Hex wrench storage (Fig. 10) When not in use, the hex wrench can be conveniently stored. Adjusting depth of cut (Fig. 11) Loosen the bolt (A) on the depth guide with the hex wrench and move the base up or down. At the desired depth of cut, secure the base by tightening the bolt (A). Bevel cutting (Fig. 12) Loosen the bolt (A) on the depth guide and the bolt (B) on the bevel scale plate with the hex wrench. Set for the desired angle (0 – 45°) by tilting accordingly, then tighten the bolts (A) and (B) securely. CAUTION: After adjusting depth of cut and bevel cutting angle, be sure to tighten the bolts (A) and (B) securely. Sighting (Fig. 13) For straight cuts, align the edge of the base with your cutting line on the workpiece. For 45° bevel cuts, align the notch in the front of the base with it. CAUTION: When making bevel cuts, view the cutting line on the workpiece through the window in the blade case in order to cut more accurately. If you have difficulty seeing it because of the water tank, adjust the position of the tank by tilting it backward slightly. Switch action (Fig. 14) CAUTION: Before inserting the battery cartridge into the machine, always check to see that the switch trigger actuates properly and returns to the ‘‘OFF’’ position when released. To prevent the trigger from being accidentally pulled, a lock-off lever is provided. To start the machine, slide the lock-off lever in the direction of the arrow and pull the trigger. Release the trigger to stop. Water supply (Fig. 15) Remove the cap on the tank and fill through the hole. Recap the tank. Be sure that the water cock is turned off when filling the tank with water. CAUTION: When filling the tank with water, be careful not to let the machine get wet. Operation (Fig. 16) Hold the machine firmly. Set the base plate on the workpiece to be cut without the wheel making any contact. Then turn the machine on and wait until the wheel attains full speed. Feed water to the wheel by adjusting the water cock to obtain a gentle flow of water. Move the machine forward over the workpiece surface, keeping it flat and advancing smoothly until the cutting is completed. Keep your cutting line straight and your speed of advance uniform. For fine, clean cuts, cut slowly. (When cutting glass plate 5 mm thick, cut at about 250 mm/min. When cutting tile 10 mm thick, cut at about 300 mm/min.) Also slow down as you complete a cut to avoid breaking or cracking the workpiece being cut. CAUTION: • Be sure to hold the workpiece firmly down on a stable bench or table during operation. • Do not twist or force the machine in the cut, or the motor may be overloaded or the workpiece may break. • Do not use the machine with the wheel in an upward or sideways position. • When cutting glass plate, it is recommended to attach a rubber plate (optional accessory) on the base of the machine to prevent the workpiece surface from being scratched. • The wheel for Model 4190D/DB is a wet-type wheel for glass and tile applications. Be sure to feed water to the wheel during operation. • If the cutting action of the wheel begins to diminish, dress the cutting edge of the wheel using an old discarded coarse grit bench grinder wheel or concrete block. Dress by pressing lightly on the outer edge of the wheel. Cutting performance The following reference table indicates the approximate cutting capacity from a single battery charge. Work-Thickness Cutting length (90°) piece 4190D 4190DB Glass 3mm 5 m 8 m 5mm 2 m 3 m Ceramic 5mm 4 m 6 m tile 10 mm 3.5 m 5.5 m CAUTION: If the machine is operated continuously until the battery cartridge has discharged, allow the machine to rest for 15 minutes before proceeding with a fresh battery. MAINTENANCE CAUTION: Always be sure that the machine is switched off and the battery cartridge is removed before carrying out any work on the machine. After use Brush off accumulation of dust on the base. To maintain product safety and reliability, repairs, maintenance or adjustment should be carried out by a Makita Authorized Service Center. NEDERLANDS Verklaring van algemene gegevens 1 Sluitplaat 0 Bout o Bout (B) 2 Batterij q Flens p Beschermkap 3 Oplaadlampje w Blokkeerpen a Zoolplaat 4 Klem hier bevestigen e Vastdraaien s Voor slijpen in rechte lijn 5 Watertank r Losdraaien d Voor verstekslijpen (45°) 6 Schroef (A) t Inbussleutel f Ontgrendelknop 7 Schroef (B) y Dieptegeleider g Trekschakelaar 8 Klem ...
Dieses Handbuch ist für folgende Modelle:Gartengeräte - 4190DB/4190DWB (412.09 kb)