Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Makita Dateigröße: 265.02 kb Dateiname: Unterrichtssprache:

Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the charger. Insert the cartridge fully into the port so that it rests on the charger port floor. 3. When the battery cartridge is inserted, the charging light color will flash in red color and charging will begin. 4. When the charging light goes out after about one hour, you may remove the fully charged battery cartridge. 5. After charging, unplug the charger from the power source. NOTE: • The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer’s batteries. • • • When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. • When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, sometimes the charging light will go out soon. If this occurs, remove the battery cartridge and re-insert it. If the charging light goes out within one minute even after repeating this procedure a couple of times, the battery cartridge is dead. Replace it with a new one. • If you wish to charge two battery cartridges, allow 15 minutes between charging on the charger. Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. 2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. 3. Charge the battery cartridge with room temperature at 10° C - 40° C (50° F - 104° F). Let a hot battery cartridge cool down before charging it. 003509 Adjusting the depth of cut Loosen the bolt (A) on the depth guide with the hex wrench and move the base up or down. At the desired depth of cut, secure the base by tightening the bolt (A). 1 2 3 1. Depth guide 2. Bolt (A) 3. Hex wrench 1 2 3 1 2 3 Bevel scale plate 2. Bolt (B) 3. Bolt (A) 1. Blade case 2. Base A B 1 2 003514 Bevel cutting Loosen the bolt (A) on the depth guide and the bolt (B) on the bevel scale plate with the hex wrench. Set for the desired angle (0° - 45° ) by tilting accordingly, then tighten the bolts (A) and (B) securely. CAUTION: • After adjusting depth of cut and bevel cutting angle, be sure to tighten the bolts (A) and (B) securely. 003519 Sighting For straight cuts, align the A position on the front of the base with your cutting line. For 45° bevel cuts, align the B position with it. NOTE: • When making bevel cuts, view the cutting line on the workpiece through the window in the blade case in order to cut more accurately. If you have difficulty seeing it because of the water tank, adjust the position of the tank by tilting it backward slightly. 003522 Switch action CAUTION: • Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To prevent the switch trigger from being accidentally pulled, a lock-off lever is provided. 1 2 To start the tool, slide the lock-off lever in the direction of the arrow and pull the switch trigger. Release the switch trigger to stop. CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. ASSEMBLY 1. Lock-off lever 2. Switch trigger 1 2 3 1 2 3 Bolt 2. Flange 3. Diamond wheel 003526 Installing or removing diamond wheel To install the wheel, first loosen the bolt with the hex wrench and remove the bolt and the flange. Then mount the wheel, the flange and the bolt. The wheel should be mounted with the Makita name on the flange side. 1 2 1. Hex wrench 2. Blade stopper pin 003527 Press the blade stopper pin and insert it through the hole in the wheel so that the wheel cannot revolve. Use the hex wrench to tighten the bolt securely. To remove the wheel, follow the installation procedure in reverse. CAUTION: • When installing the wheel, be sure to tighten the bolt securely. • Use only the Makita wrench to install or remove the wheel. 003533 Hex wrench storage When not in use, store the hex wrench as shown in the figure to keep it from being lost. 1 1. Hex wrench 003538 003538 Attach the tank holder on the tank. The tank holder should be attached around the portion shown with the dotted line. Tighten the screw (A) to the extent that the tank can still turn within the tank holder. 1 3 4 5 2 1. Tank holder installing portion 2. Tank 3. Screw (B) 4. Screw (A) 5. Tank holder 003539 Attach the tank holder onto the motor housing. Tighten the screw (B) securely. 1 1. Screw (B) 003541 Connect the cap on the end of the polyvinyl tube to the mouth of the tank. Turn the tank clockwise when making th...

Herunterladen

Geben Sie zwei Ziffern: