Login:
Sortierung : Dateiname ↑   heruntergeladen   Bewertung   Dateigröße ↑  
heruntergeladen wurde: 0   Dateigröße: 265 kb   Hersteller: Cornelius  
Kategorie: Andere Küchengeräte
@name

30.30” (BACK SIDE OF DISPENSER) 1.67” 27.40” ICE MAKER DROP ZONE 21.50” AND BIN STAT MUST FIT WITHIN THE 27.40 X 21.50” OPENING Figure 1 ! WARNING: Disconnect power to the unit before installing adaptor following all lock out / tag out procedures established by the user. Verify all of the power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to the equipment. ! WARNING: All of the attachment screws and plates must be installed as d

heruntergeladen wurde: 0   Dateigröße: 1 mb   Hersteller: Cornelius  
Kategorie: Andere Küchengeräte

heruntergeladen wurde: 2   Dateigröße: 1 mb   Hersteller: Cornelius  
Kategorie: Andere Küchengeräte

heruntergeladen wurde: 4   Dateigröße: 1 mb   Hersteller: Cornelius  
Kategorie: Andere Küchengeräte

heruntergeladen wurde: 0   Dateigröße: 379 kb   Hersteller: Cornelius  
Kategorie: Andere Küchengeräte
@name

Use extreme care not to drill into the hopper. Fasten the lid to the dispenser with four (4) #8 sheet metal screws, two on each side. 3. Seal the ice maker to the top of the dispenser as follows: (Flush with rear and left side) A. Apply beads of RTV around the opening in the lid and inside the perimeter of the ice maker outline so that the ice maker sets on the RTV. B. Set the ice maker onto the lid and position it as required. C. Wipe away any excess RTV. 4. Remove the left rear screw (onl

heruntergeladen wurde: 1   Dateigröße: 768 kb   Hersteller: Cornelius  
Kategorie: Andere Küchengeräte
@name

1000 Series 5—^ 4 © IMI Cornelius Inc., 2004-2012 4 Publication Number: 630460174IPL Refrigeration and Icemaker Illustrared Parts List Refrigeration and Icemaker Assembly Model WCC1401-A Item No. Part No. Description 1 Front End Assembly 2 63090092s Compressor, 208/230V 3 Electrical Box Assembly 4 161В70005 Condenser S 630900547 Water Level Control Assembly 6ЗВ00В4ВЗ Reed Switch Assembly б 6ЗВ090226 Thermal Expansion Valve 7 6З0900З0В Fan Motor Assembly, 208/230V В 630900309

heruntergeladen wurde: 0   Dateigröße: 481 kb   Hersteller: Cornelius  
Kategorie: Andere Küchengeräte

heruntergeladen wurde: 4   Dateigröße: 1 mb   Hersteller: Cornelius  
Kategorie: Andere Küchengeräte
@name

Wrap the eye of the wire form over the stud near the hole to the end of the wire form bracket and wrap the tube around the end of the bracket several times, insuring the tube is secure. NOTE: The bin stat must not interfere with the agitator rotation or in the path of ice falling from the ice- maker. If it interferes with the agitator or in the path of ice, bend the bracket out of the way. 8. For 22–inch wide ice makers, locate the lid opening covers (2) (item 11) as shown in Figure 1. Secure th

heruntergeladen wurde: 2   Dateigröße: 145 kb   Hersteller: Cornelius  
Kategorie: Andere Küchengeräte
@name

NOTE: Adjust the automatic agitation timer located in the dispenser’s electrical control box to 5 seconds on, 20 minutes off. Access to the timer is provided by removing the merchandiser/upper front panel. 1. Remove the top plastic bin covers (2) from the dispenser. 2. Place the ice maker adapter lid assembly (item 1) on top of the dispenser and position it flush with the rear and sides of the dispenser as shown in Figure 1. 3. Install the ice baffle on the lid assembly as shown in Figure 2. Rel

heruntergeladen wurde: 0   Dateigröße: 145 kb   Hersteller: Cornelius  
Kategorie: Andere Küchengeräte
@name

NOTE: Adjust the automatic agitation timer located in the dispenser’s electrical control box to 5 seconds on, 20 minutes off. Access to the timer is provided by removing the merchandiser/upper front panel. 1. Remove the top plastic bin covers (2) from the dispenser. 2. Place the ice maker adapter lid assembly (item 1) on top of the dispenser and position it flush with the rear and sides of the dispenser as shown in Figure 1. 3. Install the ice baffle on the lid assembly as shown in Figure 2. Rel





Kategorien