In no event shall Grizzly’s liability under paid for the product and any legal actions brought of Washington, County of Whatcom. We shall in no event be liable for death, injuries to persons special, or consequential damages arising from the use To take advantage of this warranty, contact us by mail or phone and We will then issue you a “Return Authorization Number,” which must be the outside as well as the inside of the carton. We will not accept any item number. Proof of purchase must accompan

AIR TOOL KIT Using the Spray Gun 1. Attach the paint reservoir onto the spray gun and attach the air hose. 2. Adjust the air pressure regulator on the compressor to 30 PSI. 3. Identify the spray gun controls in Figure 1 and adjust in the following order: A. Fluid Control—Adjusts how far back the trigger can be pulled, affecting the volume of finish released. B. Pattern Control—Variably adjusts the spray pattern from round to a wide fan. C. Nozzle Control—Adjusts the spray pattern from ver

Touching red and black terminal clamps together will cause a short and may cause an explosion or fire. Never touch red and black terminal clamps together! Tire Inflater The air nozzle is tucked inside the storage compartment that is located near the black terminal clamp. If you are filling a tire at night, and you are on the side of the road near oncoming traffic, use the hazard lights to increase your personal safety. To use the tire inflater: 1. Remove the cover to the storage compartment, and

6. Close the drain valve when all the water has been released. 7. Store air compressor in its normal operating position in a cool protected area. Water will condense in the air compressor tank. Water left in the tank can cause the tank to weaken and corrode, increasing the risk of tank rupture -14- Model H3370/H3371Air Compressors TROUBLESHOOTING PROBLEM CAUSE ACTION Pump motor 1. Low voltage. 1. Check power line for proper voltage. will not start 2. Open circuit in motor, switch or cord. 3. Tan

6. Inspect and replace pump piston rings. Compressor 1. Improper oil level. 1. Check oil level and add oil. knocking 2. Air filter clogged. 3. Piston assembly loose. 2. Inspect and clean air filter. 3. Inspect and repair piston and connecting rod. Motor runs hot 1. Cooling fins dirty. 2. Air filter clogged. 1. Clean cylinder fins and motor area. 2. Inspect and clean air filter. Model H3370/H3371Air Compressors -15 PROBLEM CAUSE ACTION Motor runs hot 3. Compressor is exceeding its duty- cycle. 3.

Model H3370/H3371Air Compressors AIR CONTROL Delivered Pressure The tank pressure is displayed on the left pressure gauge, and the air to be delivered to the tool is displayed on the right pressure gauge shown in Figure 6. Figure 7. Air control knob. Note—The air tool that you attach to the air compressor should have a preferred PSI operating level. Set the pressure to be delivered to the tool according to the tools preferred level. Understand the duty cycle of the air compressor. Model H3370/H3

This accessory and many like it can be found in the Grizzly Catalog. Figure 10. Quick connect couplers. Make certain the air hose will not be placed in a position where it can become constricted or cut by a sharp object. Note— Running over a hose with heavy vehicles may not cause an immediate leak, but it will shorten the life of the hose. H3372 3 HP Air Compressor Consideration should also be given to the type of usage. A nailer or staple gun uses air in short bursts and it is easier for the co

#JM9879 PRINTED IN CHINA SAFETY For Your Own Safety Read Instruction Manual Before Operating This EquipmentThe purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident preventio

PRINTED IN CHINA ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF THE MACHINE, THIS MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE . CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT DIFFERENCES. PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE. WARNING Some dust created by power sanding, sawing, grinding

For modEls mAnUFACtUrEd sinCE 02/10 #Cr12612 printEd in ChinA This manual provides critical safety instructions on the proper setup, operation, maintenance and service of this machine/equipment. Failure to read, understand and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution or death. The owner of this machine/equipment is solely responsible for its safe use. This responsibility includes but is not limited to proper installat