Login:
Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Anleitung Honeywell, modell 42710-01

Hersteller: Honeywell
Dateigröße: 2.41 mb
Dateiname: 42710.pdf
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


If you do not have both an rH and rC wire, leave the jumper in place. 2. Match and connect the wires from the wall to the terminals as shown. Wires should be inserted behind the black terminal shields. Tighten each screw after the connection has been made. (The ends of any extra wires should be individually wrapped in electrical tape and carefully pushed back into the wall.) 3. Push any excess wire length back into the wall to prevent interference. GRCRHYWJumper InSTAllInG THE THErMOSTAT, COnT. COnnECTInG THE WIrES 1. loosen, but do not remove, the terminal screws. note: A jumper wire has been provided, connecting the rC and rH terminals for systems that do not provide both an rH and rC wire. If you have both an rH and rC wire, remove this jumper. If you do not have both an rH and rC wire, leave the jumper in place. 2. Match and connect the wires from the wall to the terminals as shown. Wires should be inserted behind the black terminal shields. Tighten each screw after the connection has been made. (The ends of any extra wires should be individually wrapped in electrical tape and carefully pushed back into the wall.) 3. Push any excess wire length back into the wall to prevent interference. GRCRHYWJumper 18 DISABLE ENABLE RECOVERY HG HE W/B Y/O RH RC G SYSTEM TYPE STD HP Y1 FAN OPTION AM HEAT TThermostat Cover System Switch Fan Switch DISABLE ENABLE RECOVERY HG HE W/B Y/O RH RC G SYSTEM TYPE STD HP Y1 FAN OPTION AM HEAT TThermostat Cover System Switch Fan Switch InSTAllInG THE THErMOSTAT, COnT. ATTACHInG THE THErMOSTAT lift the thermostat cover and set the SYSTEM switch to OFF and the FAN switch to AUTO. 1. Fan option - locate the HE/HG switch on the back of the thermostat. Set the switch to HG (default) for gas furnace and oil burners. Set the switch to HE for electric furnaces. (The switch has no effect when the system is set to cooling mode.) 2. recovery - locate the AUTO REcOvERY switch on the back of the thermostat. If you wish to use the Auto recovery feature, verify that the switch is in the EnABlE position. If you do not wish to use this feature, simply change the switch to the DISABlE position. See pages 44-45 for more information. 3. System type - locate the SYSTEM TYpE switch on the back of the thermostat. Select either STD (Standard) or HP (Heat Pump) to match your system. 20 12front cover Tab 12front cover Tab InSTAllInG THE THErMOSTAT, COnT. 4. Place the top of the thermostat over the two tabs on the wall plate. Press the thermostat onto the wall plate and press to snap the bottom tab into place. note: Do not force the thermostat onto the wall plate, as the terminal pins may be damaged. If the thermostat does not snap into place properly, the unit may not work. 5. lift the front cover and insert two AA alkaline batteries. 6. restore power at the electrical panel or furnace. 22 resetreset SETTInGS The default setting of the thermostat is Fahrenheit (Fo). (nOTICE: CHAnGInG THIS SETTInG WIll rESET THE THErMOSTAT TO FACTOrY DEFAUlT PrOGrAMS.) To change to Celsius (Co): 1. Press and hold the Up button. 2. Use a paperclip to press the RESET button. 3. Continue to press the Up button, but release the reset button when the lCD turns on. To reset the unit to F, press only the RESET button. 24 day/timeAMPMprogram day/timeAMPMprogram SETTInGS, COnT. The default for this thermostat setting is in a 12 hour format. You can change the format to 24 hour format by pressing DAY/TiME and then pROGRAM. The AM/PM indicator will be off when the thermostat is in 24 hour mode. Setting day and time: 1. Press DAY/TiME. (AM/PM and current hour will flash) Press Up or DOwN to adjust the setting. 2. Press DAY/TiME again to adjust the minute setting. Press Up or DOwN to adjust the setting. 3. Press DAY/TiME again to adjust the day of the week. Press Up or DOwN to adjust the setting. 4. Press DAY/TiME to return to the normal display. Press Up or DOwN to adjust the setting. You may also press Hold/return at any time to return to the normal display. 26 AMHEATT AMHEATT METHODS OF OPErATIOn This thermostat gives you the ability to program up to...

Dieses Handbuch ist für folgende Modelle:
Steuerungen & Regelgeräte - 42710-01 (2.41 mb)
Steuerungen & Regelgeräte - 44360 (2.41 mb)
Steuerungen & Regelgeräte - 42710-01 (2.41 mb)
Steuerungen & Regelgeräte - 44360 (2.41 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien