Installation could be the problem: Your hood was designed to SMOKE/STEAM/ meet specific ducting requirements. If your duct length exceeds ODORS ADEQUATELY the manufacturer's requirements, hood performance will suffer. Air-flow will also be reduced if the house duct work is too small or there are too many elbows in the system. Contact your installer or builder. 2. Obstruction in duct work could be the problem: Make sure nothing is blocking the vent (bird nests or kinks in the duct work). 3. Dampe

C. Si vous faites un trou ou une ouverture dans un mur ou un plafond, n’endommagez pas les fils electriques et les autres installations cachees de service public. D. Vous devez toujours alimenter les ventilateurs dans les conduits en air en provenance de l’exterieur. AVERTISSEMENT : POUR REDUIRE LE RISQUE D’INCENDIE, N’UTILISEZ QUE DES CONDUITS EN METAL. • N’essayez jamais de remplacer ou de reparer un element de votre hotte si le present manuel ne le recommande pas expressement. Tout autre entr

Do not use abrasives or oven cleaners. Rinse, shake and let them dry before replacing. They may also be cleaned in an automatic dishwasher. To remove: Grasp the baffle knobs and pull them up, forward and out. Grasp the drip tray and carefully lift it up and out of the hood track. To replace the drip trays: 1. Place and seat the drip tray into the hood track. 2. Slide them left or right until all trays are side-by-side in place in the track. To replace the baffles: 1. Hold the baffle at the botto

. 11 Model and Serial Numbers. . 2 Owner’s Registration for Canadian Customers. . 9 Problem Solver. . 8 Safety Instructions. . 3 Warranty. . 12 Controls and Features. . 4 Care and Cleaning Charcoal Filter. . 6 Drip Tray. . 7 Hood Surfaces. . 6 Light Bulbs. . 7 Metal Baffle Grease Filter. . 6 Before using your stainless steel hood Read this manual carefully. It is intended to help you operate and maintain your new stainless steel hood properly. Keep it handy for answers to your questions. If you

To replace the baffles: 1. Hold the baffle at the bottom by one of the knobs . 2. Place the other end of the baffle against the inside front of the hood. 3. Slide it up and push the bottom end back until it firmly seats into place. Drip Tray Drip Tray Track Drip Tray Replacement Baffle Baffle Replacement Care and Cleaning Professional Range Hood Stainless steel Do not use a steel wool pad; it will scratch the surface. To clean the stainless steel surface, use warm sudsy water, a stainless steel

And you can call any time. GE Answer Center® service is open 24 hours a day, 7 days a week. OR Visit our Website at: A GE consumer service professional will provide expert repair service, scheduled at a time that’s convenient for you. Many GE Consumer Service company-operated locations offer you service today or tomorrow, or at your convenience (7:00 a.m. to 7:00 p.m. weekdays, 9:00 a.m. to 2:00 p.m. Saturdays). Our factory-trained technicians know your appliance inside and out—so most repairs c

N’utilisez cet appareil que de la maniere prevue par le fabricant. Si vous avez des questions, appelez le fabricant. B. Avant de reparer ou de nettoyer votre appareil, debranchez le courant au niveau du panneau de service et verrouillez les mecanismes de debranchement de service pour eviter tout branchement accidentel au courant. Si vous ne pouvez pas verrouiller les mecanismes de debranchement de service, attachez soigneusement un avertissement bien visible, comme une etiquette, au panneau de s

Allow additional clearances below the burner box to install the regulator and make house gas supply connections. Use a 90° elbow to route the gas connections and limit interference with drawers or other cabinetry features. For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at GEAppliances.com or call GE Answer Center® service, 800.626.2000. ZGU48N4GHSS (Natural Gas) ZGU48L4GHSS (Liquid Propane) – GE Monogram 48" Professional Gas Cooktop with 4 Burners, Grill

ZGU48N4GHSS with 4 burners, grill and griddle (Order ZGU48L4GHSS for LP gas) Product Dimensions and Clearance A 48"-or 54"-wide professional vent hood with a minimum 1200 CFM is recommended for installation over this cooktop. • Install the hood 30" to 36" above the cooking surface Clearances between cooktop and side wall or combustible material must be at least 12" on each side. 8" 2-1/2" 7/8" 46-1/8" 22-3/4" 26-5/8" 8-7/16" 47-7/8" MonogramFRONTREARHEATINGFRONTREARFRONTREARAllow Clearance Below

Box 1592, York, Pennsylvania USA 17405-1592 Copyright © by York International Corporation 2004 Form 115.23-RP1 (1104) New Release Tele. 800-861-1001 Subject to change without notice. Printed in USA ALL RIGHTS RESERVED