General Unpack the heater carefully and retain the packaging for possible future use, in the event of moving or returning the fire to your supplier. Loose coals are packed separately within the carton. When the heater is assembled the coals are placed on top off the fuel bed. The heaters is designed for use inset into a 407mm (16”) or 457mm (18”) wide by 559mm (22”) high fireplace opening see also section “Installation in a fire place opening”. A 2kw fan heater discreetly positioned in the canop

Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician. contempraef INSTALLATION 1. Make sure the unit is switched OFF (refer to operating instruction section). 2. Plug the unit into a 15Amp/120volt outlet. If the cord does not reach, you may use an extension cord rated for a minimum of 1875 watts. OPERATION To access the controls go to the front panel of the unit (refer to diagram below) 1. Thre

• A means for disconnection must be incorporated in the fixed wiring by a double pole switch with a contact separation of a minimum of 3mm and in accordance with the current IEE Wiring Regulations. • The heater must not be installed immediately below a fixed socket outlet. • The heater is not suitable for connection to a 30A ring circuit. • Do not position the heater under windows where curtains can contact the heater casing. • WARNING - THE SURFACES ON THIS HEATER CAN BE HOT. • This heater meet

It is designed for permanent wall mounting and is suitable for operation on A.C. electricity supply having the same voltage as shown on the rating label. The heater is fitted with an internally mounted selector switch which on installation of the heater allows a choice of 1kW or 2kW output to suit the dimensions of the room to be heated. In rooms of less than 9 – 11 cubic m. (350 - 400 cubic ft.) 1kW output should be selected, otherwise nuisance tripping of the thermal overload cut-out may occur

08/15981/3 Issue 3 Fig. 2 Fig. 4 Installation Procedure It is essential to observe minimum wall mounting clearances - see Fig. 1. The appliance should be fitted horizontally, with the cable entry at the top and grille at the bottom. It must be mounted not less than 1800mm above the floor with a clearance of at least 600mm to any shelf or projecting surface below the heater and not less than 300mm below the ceiling or other projecting surface. It must also be not less than 250mm from an adjacent

C. HEATER THERMOSTAT CONTROL To adjust the temperature to your individual requirements, turn the thermostat control clockwise all the way to turn on the heater. When the room reaches the desired temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in this position to maintain the room temperature at this setting. For additional heat, turn clockwise until you hear the click again and the heater will turn on. RESETTING THE TEMPERATURE CUTOFF SWITCH Should the heate

* When the heat control is set to ‘ ‘ for cool blow, set the thermostat control to maximum. Position ‘ ‘ will turn the heater on and off to maintain a temperature of approximately 5°C. - OFF - Cool Blow* - Half heat - Full heat Heat Control - see Fig. 2 (IP21) H W D 265 230 230 Model(s) Specification DXUFSR2 2.0kW Thermostat & Switch Fig. 2 Fig. 3 (see Fig. 3) Fig. 1 (see Fig. 2) IMPORTANT SAFETY ADVICE DO NOT use the heater on deep pile carpets or the long hair type of rugs, or less than 750mm

When replacing the fuse, a 13 amp fuse approved by ASTA to BS 1362 must be used. If the plug is not suitable for the socket outlets in your home, the plug must be cut off and an appropriate one fitted. A plug cut off from a mains lead will give a shock hazard if inserted into a 13 amp socket elsewhere in the house. To avoid this, it should be disposed of immediately. Using the Heater Thermostat Control - see Fig. 3 The heat output is controlled by the thermostat, according to the room temperatur

To avoid this, it should be disposed of immediately. Using the Heater Thermostat Control - see Fig. 3 The heat output is controlled by the thermostat, according to the room temperature. Turn the thermostat knob fully clockwise to maximum setting initially. When the room is warm enough, reduce the setting slowly until the heater just clicks off. The heater will now cycle on and off to maintain your selected room temperature. An audible click may be heard when the thermostat operates - this is nor

Models with Timer DXLWP400TI, DXLWP800TI N & ARLWP800TI Set the I - .......... - O slide switch on the timer (Fig. 3) to : Position O - Heating Off Position I - Manual operation This setting allows power to the heater uninterrupted by the timer settings. The heat selector switch will control the output (see ‘Using the heater’). Position .......... - ‘Auto’ operation DO NOT disconnect this heater from the mains supply unless it is being taken out of use (e.g. in summer or for storage), otherwise