2Step Insert the mounting springs into the slots and mount the grille to the body. 5Step Insert the duct into the duct connector. 3Step 4405 Cushing Parkway | Fremont, CA 94538 tel 1.888.979.9889 | DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY Delta Electronics Inc.(“ Delta Electronics” ) warrants to the original consumer purchaser in the USA that the Breez ventilation fan products will be free from defects in material or workmanship. This warranty is limited to three (3) years from the original

5-3. Ensure the distance between ceiling and fan body for the thickness of grille. 5-4. Secure the suspension bracket to joists by using screw. 5-5. Secure the suspension bracket to fan body by using screw. 5-6. Follow step 6 to 9 of installation to complete the installation work. 6. Duct Connection Outside Gradient 1°~2°Inspection Hole Grill Body Tape Duct Inside Ceiling 6-1. Insert the duct into the duct connector and tape all ductworks connection to make them secure and air tight. 6-2. Instal

6-2. Install the duct with a gradient 1°~2° to the outside. 7. Connect Wiring 7-1. Follow all local electrical and safety codes. 7 -2. N EVER place a switch where it can be reached from a tub or shower. 7-3. Connect wires as shown in wiring diagrams. 7-4. Using wire nuts, connect house power wires to ventilating fan wires. 7-5. 14 AWG (2.1 mm2) is the smallest conductor that shall be used for branch-circuit wiring. 8. Test Run and Grille Attachment 8-1. With the power on, check for abnormal vibr

Ventilation Fan Installation Guide The Breez Ventilation System is easy to install Two basic types of installation are shown: in new or existing construction. Body Wood Frame Installation Joist Mounting Installation Make sure that the dimensions of the opening are suitable for installation and follow the steps below. Joist Joist Wood Frame Step 1 Attach the duct connector to the wood frame with taping screw. Wood Frame Wood Frame Duct Connector Taping Screw Step 2 Insert the body into the wood f

2. Make sure that the electric service supply voltage is AC 110~220V, 50~60Hz. 3. Follow all local electrical and safety codes, as well as the Nation Electrical Code (NEC) and the Occupation Safety and Healthy Act (OSHA). 4. Always disconnect the power source before working on or near the ventilating fan, motor or junction box. 5. Protect the power cord from sharp edges, oil, grease, hot surfaces, chemicals or other objects. 6. Do not kink the power cord. 7. in Fig. A. 8. Provide suction parts w

10. panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 11. NEVER place a switch where it can be reached from a tub or shower. 12. Not to be installed in a ceiling thermally insulated to a value greater than R40 (This is required for installation in Canada only). CAUTION 1. For general ventilating use only. Do not

ÁbELU № JÍMI * Bearing Type Ball Bearings * Material Impeller & Frame : Plastic (UL 94V-0) * Lead Wires : UL 1430 AWG #22 OR Equivalent Red Wire Positive (+) Black Wire Negative (-) * Weight : 330g (11.64 oz) @FR 120 x 120 x 38 MM SERIES DIMENSIONS DRAWING P & Q CURVE (AT RATED VOLTAGE) QFR12/24/48XE MOUNTING PANEL CUTOUT OUTLET SIDE INLET SIDE 1.44 1.20 ^ 0.96 ¡1 0.72 w CL 0.48 0.24 0 O 40 80 120 160 200 Air Flow <=> (CFM) (INCH) 120.0 ± 0.5 38.0 ± 0.5 0 MODEL

asured in anechoic chamber in free air, one meter from intake side. * All readings are typical values at rated voltage. * Specifications are subject to change without notice. 42 http://www.deltaww.com

air flow and the speed are measured in free air ; max. air pressure is measured at zero air flow. * Noise is measured in anechoic chamber in free air, one meter from intake side. * All readings are typical values at rated voltage. * Specifications are subject to change without notice. 42 http://www.deltaww.com

air flow and the speed are measured in free air ; max. air pressure is measured at zero air flow. * Noise is measured in anechoic chamber in free air, one meter from intake side. * All readings are typical values at rated voltage. * Specifications are subject to change without notice. 42 http://www.deltaww.com