28 MSG sheet metal, 0.015" stainless steel, 0.024" aluminum, or 0.020" copper. 30" min. clearance when the cabinet is unprotected. **Note: Minimum cutout depth is increased to 24" with optional backguard. tNote: To avoid cooktop glass breakage for cutout width of more than 30 1/16", make sure appliance is centered in the counter opening while pushing into it. ttFor cutouts below 22 7/8”, appliance will slightly show out of the cabinet. +Allow at least 20" clearance for door depth when it is ope

Unscrew these 4 screws until the burners are at their proper location (figure 6). Figure 6 3. Provide an Adequate Gas Supply the cooktops covered in these instructions are designed to operate on natural gas at 4" of manifold pressure or on LP gas at 10" of manifold pressure. A convertible pressure regulator is supplied with each surface unit and MUSt BE CONNECtED iN SERiES between the supply line and the valve manifold regardless of which type of gas is being used. the convertible regulator for

01/05 4 790.4274 MAIN TOP/SURFACE UNITS CAUTION: Use the Kenmore part number to order part, not the illustration number. Model Index: A 790.4274 (790.42741402) B 790.4274 (790.42742401) C 790.4274 (790.42743401) D 790.4274 (790.42744401) E 790.4274 (790.42749401) POS. NO PART NO. DESCRIPTION 15 # 15A# 318198817 316277700 A A B B C D E C D E Element, surface, small/6", 1200 W Element, surface, 9", 3000W, radiant 15B# 15C# 16 16 16 16 16 20 318198925 318199101 318282506 318282500 318282503 3182825

01/05 4 790.4274 MAIN TOP/SURFACE UNITS CAUTION: Use the Kenmore part number to order part, not the illustration number. Model Index: A 790.4274 (790.42741402) B 790.4274 (790.42742401) C 790.4274 (790.42743401) D 790.4274 (790.42744401) E 790.4274 (790.42749401) POS. NO PART NO. DESCRIPTION 15 # 15A# 318198817 316277700 A A B B C D E C D E Element, surface, small/6", 1200 W Element, surface, 9", 3000W, radiant 15B# 15C# 16 16 16 16 16 20 318198925 318199101 318282506 318282500 318282503 3182825

• Do not leave children alone—Children should not be left alone or unattended in the area where an appliance is in use. They should never be allowed to sit or stand on any part of the appliance. • DO NOT TOUCH SURFACE BURNERS, GRATES, AREAS NEAR THESE BURNERS. Surface burners may be hot even though the flames are not visible. Areas near surface burners may become hot enough to cause burns. During and after use, do not touch or let clothing or other flammable materials touch these areas until the

Failure to follow instructions could result in serious injury or property damage. The qualified agency performing this work assumes responsibility for the conversion. Liquefied Petroleum (Propane) Gas Conversion 6 Setting Surface Controls The color of the flame is the key to proper burner adjustment. A good flame is clear, blue and hardly visible in a well-lighted room. Each cone of flame should be steady and sharply defined. Adjust or clean burner if flame is yellow-orange. To clean burner, see

WARNING This appliance is equipped with a 3-prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded receptacle. DO NOT cut or remove the grounding prong from this plug. For personal safety, this cooktop must be properly grounded. For maximum safety, the power cord must be plugged into a 120V—60 Hz. outlet that is correctly polarized and properly grounded. If a two-prong wall receptacle is the only available outlet, it is the personal

2 Important Safety Instructions ...................................... 3-4 Selecting Surface Cooking Utensils..................................5 Specialty Pans & Trivets ................................................... 5 Canning Tips & Information ............................................. 6 Grounding Instructions....................................................6 Liquefied Petroleum (Propane) Gas Conversion ............... 6 Flame Size....................................................

Commercial glass cleaners recommended for glass cooktops may also be used. Wipe the control panel clean after each use. Before cleaning the control panel, turn all controls to OFF and remove the control knobs. To remove, pull each knob straight off the shaft. Clean using hot, soapy water and a cloth. Be sure to squeeze excess water from the cloth before wiping the panel; especially when wiping around the controls. Excess water in or around the controls may cause damage to the appliance. To repla

Wire trivets: Do not use wire trivets. Cookware bottoms must be in direct contact with the surface elements. 6 Setting Surface Controls 1. Place the pan on the surface element. 2. Push in and turn the surface element control knob to desired setting. 3. The surface signal light will glow when one or more elements are turned on. Always turn the element off before removing the pan. The suggested settings found in the chart below are based on cooking in medium-weight aluminum pans with lids. Setting