Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Commercial glass cleaners recommended for glass cooktops may also be used. Wipe the control panel clean after each use. Before cleaning the control panel, turn all controls to OFF and remove the control knobs. To remove, pull each knob straight off the shaft. Clean using hot, soapy water and a cloth. Be sure to squeeze excess water from the cloth before wiping the panel; especially when wiping around the controls. Excess water in or around the controls may cause damage to the appliance. To replace knobs after cleaning, line up the flat sides of both the knob and the shaft; then push the knob into place. Surface elements can be unplugged and removed to make cleaning the drip bowls easier. The surface elements clean themselves when they are turned on. Food spilled on a hot element will burn off. Food spilled on a cool element can be cleaned with a damp cloth—any remaining soil will burn off the next time the element is used. NEVER IMMERSE A SURFACE ELEMENT IN WATER. To remove surface elements and drip bowls, follow the instructions under General Cleaning. To clean drip bowls, wash in hot, soapy water or in the dishwasher. Rinse and dry while still warm. Hard-to-remove, burned-on soils can be removed by soaking the drip bowls for about 20 minutes in a slightly diluted liquid cleanser or a solution made of equal parts ammonia and water. A nylon scrubber may be used after soaking. DO NOT use abrasive cleansers or steel wool, as they will scratch the surface. Always rinse with clean water and polish, and dry with a soft cloth or paper towel. To replace drip bowls and surface elements, follow the instructions under General Cleaning. Gentle scouring with a soapy scouring pad will remove most spots. Rinse with a 1:1 solution of clear water and ammonia. If necessary, cover difficult spots with an ammonia-soaked paper towel for 30 to 40 minutes. Rinse with clean water and a damp cloth, and then scrub with a soap-filled scouring pad. Rinse and wipe dry with a clean cloth or paper towel. Remove all cleaners or the porcelain may become damaged during future heating. DO NOT use spray oven cleaners on the cooktop. Cover stubborn spots with an ammonia-soaked paper towel for 30 to 40 minutes. Rinse with clean water and a cloth. A soapy, nylon mesh scouring pad may be used carefully on stainless steel; not on chrome. Cleaners made especially for stainless steel, chrome or copper are also recommended. Do not use metal-type scouring pads on brushed chrome. This could cause the brushed chrome to change to a yellowish tint. Rinse all cleaners before operating cooktop. Bluish stains may result due to heat combining with the cleaning material and they cannot be removed. See Ceramic-Glass Cooktop in this Owner's Guide. Surfaces Aluminum (Trim Pieces) Glass, Painted and Plastic Control Knobs, Body Parts, and Decorative Trim Control Panel Surface Elements and Drip Bowls Porcelain Enamel Cooktop Chrome (brushed) Decorative Trim Cooktop Ceramic -Glass Cooktop Be careful not to bend terminal ends when replacing elements after cleaning. Be careful not to bend terminal ends when replacing elements after cleaning. General Cleaning (Continued) To Remove and Replace Surface Elements and Drip Bowls Before cleaning the cooktop, be sure the controls are turned to OFF and the cooktop is COOL. To Remove 1. Lift up edge of surface element across from terminal end just enough to clear the edge of the drip bowl. 2. Gently slide the surface element out of the terminal plug. 3. Lift the drip bowl up and out. To Replace 1. Line up the opening of the drip bowl with the terminal plug. 2. Hold the surface element as level as possible and slide the terminal end through the opening and into the terminal plug. 3. Be sure the surface element is level to reduce the hazard of pans sliding off the element. To Raise the Top for Cleaning 1. Grasp the sides and lift from the front. Some models may have a lift-up rod to support the top in its raised position. Lift the top only high enough to allow the support rod to fit into place, then gently lower the cooktop onto the raised rod. 2. Clean underneath using a clean cloth and hot, soapy water. 3. Gently lower the cooktop into the frame. If your model has a support rod, lower the support rod, then gently lower the cooktop into the frame. When lowering the lift-up cooktop, grasp the sides with fingertips only. Be careful not to pinch fingers. DO NOT drop or bend the cooktop when raising or lowering. This could damage the surface. Avoid Service Checklist Before you call for service, review this list. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance. OCCURRENCE POSSIBLE CAUSE/SOLUTION Entire cooktop does not operate. House fuse has blown or circuit breaker has tripped. Check/reset breaker or replace fuse. If the problem is a circuit overload, have this situation corrected by a qualified electrician. Service wiring not com...