Please Note: You may need to push out on the center panel and arched panel while pushing down on the platform. * insert the stair pegs into the middle holes on the arched pane) and center panel. Helpful Hint: )n the stairs position, the ladder peg bar rests on the ground. • To secure the platform: - Align the screw holes in the center panel and platform. You may need to slightly adjust the position of the platform to align the holes. Helpful Hint: To make sure the screw holes are aligned,

Adult assembly is required. Requires four “C” (LR14) alkaline batteries for the mobile and two “AA” (LR6) alkaline batteries for the remote control. (Batteries not included) Di s c o v e r w h a t ’s possible™ Tool required for battery installation: Phillips screwdriver (not included). Parts 2 • A crib mobile is intended for visual stimulation and not to be grasped by a child. • Always attach by provided fastener (clamp) tightly to a crib or playpen according to the instructions. Check frequentl

• Pull on the ball return to be sure all six ends are fastened to the rim. 3 Assembly Assembly 4 2 Side Edge Side Edge3 5 1 Proper label application will help to keep the label looking its best! • Make sure the area where the label will be applied is clean and dry. Wipe the backboard with a clean, soft, dry cloth to remove any dust or oils. • For best results, avoid applying the label more than once. • Peel the backing from one half of the label. Do not remove all of the backing! • Align the sid

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can

90 ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY Straps SIDE VIEW STEP 79 • Remove the fabric from the straps on each side of the chute (there are five on each side). Throw the fabric away. • Wrap the straps on each side of the chute around an adjacent loop in the net and fasten. 91 Straps BACK VIEW Straps BACK VIEW STEP 80 • Remove the fabric from the straps. Throw the fabric away. • Wrap the straps on the top, left side of the chute around the wires and the tube. Fasten the straps. 92 ASSEMBLYASSEMBLY Str

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Assembly Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Decoration . . . . . . . . . . . . . . . . .

• Carefully apply the side edge of the label to the side edge of the label area on the backboard. • While rubbing the label in place, continue to peel the backing from the other half of the label. • After applying the label, rub the label firmly with a cloth to make sure the label is adhered to the backboard. • Dispose of the label backing properly. Backboard Assembly 3 1 2 Side Edge Base “T” End Plug • Place the loops at the top of the net into the grooves on the ring. • Pull each loop through

Rectangular Tab Rim Upper Post • Lean the rim against a wall for support. • Locate the pegs on each side of the rim and the grooves on the backboard. • Position the backboard with the Fisher-Price® logo facing up. • Place your foot on the base to hold it steady and slide the backboard onto the upper post at an angle, as far as it will go. Note: There should be no gap between the upper post and the backboard. • Move the assembly away from the wall. 6 4 5 Backboard Fisher-Price® Logo Peg Groove Wa

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

Adult assembly is required. Tool required for assembly Phillips screwdriver (not included). 3-In-1 Gym H8096 Instructions Please keep this instruction sheet for future reference,as it contains important information. Adult assembly is required. Tool required for assembly Phillips screwdriver (not included). Parts To prevent entanglement injury, never place the gym in a crib or playpen. Never add strings, ties or other products to the gym. Part Not Shown: 4 Toys Green Arch Blue Arch 2 Hubs This to