Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
• Pull on the ball return to be sure all six ends are fastened to the rim. 3 Assembly Assembly 4 2 Side Edge Side Edge3 5 1 Proper label application will help to keep the label looking its best! • Make sure the area where the label will be applied is clean and dry. Wipe the backboard with a clean, soft, dry cloth to remove any dust or oils. • For best results, avoid applying the label more than once. • Peel the backing from one half of the label. Do not remove all of the backing! • Align the side edge of label 1 (where backing is removed) with the side edge of the label area on the backboard. • Carefully apply the side edge of the label to the side edge of the label area on the backboard. • While rubbing the label in place, continue to peel the backing from the other half of the label. • Apply the remaining labels to the backboard. Labels 2-5 are designed to overlap. • Dispose of the label backing properly. Plug“T” End Base6 • Bend the “T” end of the plug and insert it into the hole in the base. Note: After assembly is complete, fill the base with water or approximately 50 lbs. (22.7 kg) of sand (water and sand not included) to keep this product stationary. Simply lift the plug, fill the base, and replace the plug. 4 5 6 Large Square Opening Base Upper Post Curved End 7 • Position the base as shown. • Position the upper post so that the straight end is down and the curved end is up and facing away from the base. Hint: For easier assembly, apply liquid soap or rub a candle or bar soap around the bottom of the upper post (especially on the corners) and the inside of the large square opening. If assembling inside, place a tarp under the base to protect the floor surface. • Insert the upper post into the large square opening in the base and, using a circular motion, push it all the way down. 4 56• Hook the rectangular tab on each side of the rim to the upper post, as shown. • Rotate the rim down until it snaps into place on the upper post. Push down on the rim to be sure it is secure. Rectangular Tab Rim Upper Post 8 4 Assembly 645Backboard Fisher-Price® Logo Peg Groove Wall Rim Upper Post 9 6 45Lower Post Rib Groove Base 11 • Lean the rim against a wall for support. • Locate the pegs on each side of the rim and the grooves on the backboard. • Position the backboard with the Fisher-Price® logo facing up. • Place your foot on the base to hold it steady and slide the backboard onto the upper post at an angle, as far as it will go. Note: There should be no gap between the upper post and the backboard. • Move the assembly away from the wall. PULL HERE FsherPriceTop View PRESS HERE Peg Peg Grooves Back View 10 • Move to the side of the assembly. • Place your foot on the base to hold it steady. • Press down firmly on the lower backboard while rotating the backboard up. • When properly assembled, the pegs on the upper post rest in the grooves in the backboard, as shown. Note: The height of the rim is three feet (1 m) as assembled. IMPORTANT! Assembly of the lower post to the base is a permanent assembly. • Align the rib on the bottom of the lower post with the groove in the opening in the base. Hint: For easier assembly, apply a small amount of liquid soap around the bottom of the post. If assembling indoors, place a tarp under the base to protect the floor surface. • Insert the lower post into the opening and push down, using a circular motion, until it snaps into place. Note: The collar may already be factory assembled. • Align the lever on the side of the collar with the opening in the top of the lower post. • Fit the collar onto the lower post, making sure the peg on each side of the collar snaps into the hole on each side of the post. Collar Lever Opening Lower Post Hole Peg 12 5 Assembly Care and Maintenance Assembly Care and Maintenance Peg Peg Holes • If the lever comes off, simply re-attach it. • Insert the peg on one side of the lever into the hole in the collar. • Snap the other peg in the lever into the other hole in the collar. Assembly is now complete. Please refer to assembly step 2 to fill the base with water or approximately 50 lbs. (22.7 kg) of sand (water and sand not included) to keep this product stationary. • This toy includes an inflatable ball. If the ball becomes soft, inflate it with a standard, manual air pump with a standard air needle. • The ball will contain the correct amount of air when its circumference measures about 21-22 inches (53-56 cm). Measure the circumference of the ball with a tape measure or with a piece of string cut 21-22 inches (53-56 cm) long. Do not over-inflate the ball. • To clean, use a clean, damp cloth. Be sure to remove soap residue. • Do not immerse this product. • Do not leave this toy outside in freezing weather. Water left inside the base will freeze and possibly damage the b...
Dieses Handbuch ist für folgende Modelle:Kraftstationen - J5970 (457.42 kb)