It also performs general scratch start DC TIG. The Champion 10,000 offers a “no-nonsense” warranty. The engine is warranted separately by the engine manufacturer. Comes complete with 15 ft Work Cable and Clamp, and 20 ft Welding Lead and Electrode Holder! FEATURES BENEFITS You get a generator andwelder for about what you would pay for just a generator! Smooth arc starts with minimal “sticking”. Extraordinary motor starting characteristics. Strong continuous rating to run compressors, pumps, ligh

With the OHV design, automatic idle and 10 gallon fuel tank, you can expect to put in long hours before having to stop and refuel. For example: • Welding at 125 amps, 100% duty cycle, uses about 1 gal of fuel every hour. • While not welding, the engine drops to idle speed using about 1/2 gal of fuel every hour. • On a typical job using 1/8-in 7018 electrodes (125 amps, 20% duty cycle) you can expect over 16 hours of operation. • Under a continuous load of 4,000 watts of auxiliary power, the Cham

2-2. Manufacturer’s Rating Label For CE Products S-181 265-A EN 60974-1 X 100% 35% 16A/86V 27A/90V U0 = 255V I2 16A 27A U2 86V 90V IP 23 50 Hz1 I1max = 34AU1 = 115V I1max = 17AU1 230V I1eff = 20.5A I1eff = 10.2A 1 2-3. Symbols And Definitions A Amperes Plasma Arc Cutting (PAC) Adjust Air/Gas Pressure Low Air Pressure Light V Volts Increase No . Do Not Do This Temperature Protective Earth (Ground) Single Phase Constant Current Voltage Input On Off Percent Direct Current U0 Rated No Load Voltage (

OM-210 088 Page 16 OM-210 088 Page 17 3-9. Threading Welding Wire 1 Wire Spool 2 Welding Wire 3 Inlet Wire Guide 4 Pressure Adjustment Knob 5 Drive Roll 6 Outlet Wire Guide 7 Gun Conduit Cable Lay gun cable out straight. Tools Needed: 7 1 3 6 4 5 6 in (150 mm) Pull and hold wire; cut off end. 4 in (102 mm) Tighten Remove gun nozzle and contact tip. Open pressure assembly. Push wire thru guides into gun; continue to hold wire. Close and tighten pressure assembly, and let go of wire. Hold wire ti

2 3 800 576-B 1 Equipment Grounding Terminal 2 Grounding Cable Use #10 AWG or larger insulated copper wire. 3 Ground Device Ground generator to system earth ground if supplying power to a premises (home, shop, farm) wiring system. 4-4. Engine Prestart Checks (Kohler-Powered Units) Ref. 802 512-A Full Full Gasoline 1/2 in (13 mm) Follow run-in procedure in engine manual. Check all fluids daily. Engine must be cold and on a level surface. Unit is shipped with 10W30 engine oil. Engine stops if oi

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 17. . . . . . . . . . . . . . . . 407611-2 . . . WASHER, nylon shaft 1/4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 18. . . . . . . . . . . . . . . . . . 203 666 . . . WASHER, non-rotating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 19. . . . . . . . . . . . . . . . . . 203 544 . . . NUT, hub spool . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-1. Symbol Usage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . .

802 456 1 2 3 45 Tools Needed: 3/8, 7/16 in OM-944 Page 12 Return To Table Of Contents 4-3. Process/Polarity Table Process Polarity Cable Connections Cable To Gun Cable To Work GMAW . Solid wire with shielding gas DCEP . Reverse polarity Connect to positive (+) output terminal Connect to negative (.) output terminal FCAW . Self-shielding wire . no shielding gas DCEN . Straight Polarity Connect to negative (.) output terminal Connect to positive (+) output terminal 4-4. Changing Polarity 1 Lead C

As Voltage switch setting increases, wire speed range also increases (see weld setting label in welding power source or Section 6-2, as applicable). 2 Power Switch 3 Voltage Switch The higher the selected number, the thicker the material that can be welded (see weld setting label in welding power source or Section 6-2, as applicable). Do not switch under load. Switch must “click” into detent position. 4 Trigger Switch When pressed, energized wire feeds and shielding gas flows. Ref. 228 178-A /

. . . . . . . . . . . . . . . . . . . . . . 1 ... 28. . . . . . . . . . . . . . Fig 6-2 . . PANEL, front w/components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . . 153 369 . . KIT, label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 *Recommended spare parts. +When ordering a component originally displaying a precautionary label, the label should also be ordered.