11 CONEXIONES .........................................................13 CONEXION DE LOS ALTAVOCES SUMINISTRADOS ....13 CONEXION DEL CORDON CA ......................................... 13 CONEXION DE LAS ANTENAS ........................................15 CONTROL REMOTO ....................................m.....m....m....m.m.ml7 OTRAS CONEXIONES ......................................................l7 PREPARATIVES .....................................................l9 ANTES DELAOPERACION ......

When a station is stored, a preset number is assigned to the station. Use the preset number to tune in to a preset station directly. 1 Turn the FUNCTION selector to select theTUNER function, and press the VIDEO 1/5.1 CH/BAND button repeatedly to select the desired band. Then press the UP or DOWN button to select a station. 2 Press the ENTER button to store the station. A preset number assigned to the station, beginning from 1 in consecutive order for each band, is displayed for two seconds. 3 Re

NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.” Owner’s record For your convenience, record the model number and serial number (you will find them on the rear of your unit) in the space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty. Model No. Serial No. (Lot No.) AV-D25 Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating Instructions for future reference

Be sure to set the FRONT SPEAKERS A and B buttons to 10FF. Otherwise sound is output from the speakers. The 5.1 CH function, Dolby Pro Logic or DSP system is automatically canceled when the headphones are plugged in. To turn the unit off, press the POWER button. 7 ENGLISH DOWN,UP VOLUME VOL I MUTING I BALANCE T-BASS VOLUME CONTROL Turn the VOLUME control on the unit, or press the VOL buttons on the remote control. The vc)lume level is shown on the display for four seconds. It can be adjusted bet

it can store a total of 30 signal codes of the external remote control. Use the remote control. 1 Press the LEARN button. “ADDRESS flashes on the display window. 2 Press one of the MEMORY buttons (A-O), then the ADDRESS 1 or 2 button to designate the button on which the signal code is stored. The indication you designated appears on the display. Example: When designating the ADDRESS 1 on the MEMORY A button. 3 Pointing the remote control of the connected equipment toward the unit, press the func

“TAPE ON” appears on the display for four seconds, and then the source name selected in step 1 comes back on. To cancel the tape monitor, press it again so that “TAPE oFF” appears. . Any sound control except the BBE system has no effect on recording (see page 7). Recorded sound cannot be monitored if the connected tape deck is not a three-head system. 9 ENGLISH DIRECT TUNING MONO 1,2 3 DOWN~, UPA TUNER I II 1 Press the TUNER button repeatedly to select the desired band. ~ If the power is turned

There are four modes with matching graphic equalization modes. Equalization modes are selected automatically and can also be selected or turned off to suit your preference. Press one of the DSP buttons (DANCE:, LIVE, HALL or ARENA). The selected mode name appears on the display for two seconds, and the selected DSP and matching GEQ modes on the display are enclosed with parentheses. DANCE ||lliÉpf rIALL Selected mode- '-TiTiT HALL ARENA : ■; ; ; i\ i i ! JJ i 1 1 s«! L. L. Selected D

09-005-422-5T3). • This Service Manual contains information about the difference between Z-L200 (LH) and Z-L200 (HA). If requiring other information, see Service Manual of Z-L100 (U) / 200 (LH), (S/M Code No. 09-99C-422-5R1). DATA S/M Code No. 09-006-422-5S1 • If requiring information about the CD mechanism, see Service Manual of AZG-1, (S/M Code No. 09-001-335-3NC). SPECIFICATIONS Tuning range 87.5 MHz to 108 MHz Usable sensitivity (IHF) 13.2 dBf Antenna terminals 75 ohms (un

• The unit plays only the audio tracks if a disc contains both audio tracks and MP3 files. • When playing a disc of 8k bps or VBR*, the elapsed playing time in the display window will not be correct and also the intro play may not function properly. * VBR: Variable Bit Rate Notes on indications in the display • Up to 32 characters are displayed for the name of an album or a track. Characters other than uppercase letters (“A” to “Z”), lowercase letters (“a” to “z”), numerals (“0” to “9”), and und

When the front speakers are turned on, “SP3” lights up on the display window. NOTE • When you turn off the front speakers, the surround mode (Dolby Digital, Dolby Pro Logic or DTS) or the DSP mode will be canceled. • When the front speakers are turned off, SURROUND and DSP on the front panel cannot be used. (“CAN’T USE” will be displayed). CONNECTING THE SUPPLIED ANTENNAS 2 22222 Connect the FM antenna to the FM 75. terminal and the AM antenna to the AM LOOP jack. FM antenna ANTENNA AM LOOP FM 7