Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Be sure to set the FRONT SPEAKERS A and B buttons to 10FF. Otherwise sound is output from the speakers. The 5.1 CH function, Dolby Pro Logic or DSP system is automatically canceled when the headphones are plugged in. To turn the unit off, press the POWER button. 7 ENGLISH DOWN,UP VOLUME VOL I MUTING I BALANCE T-BASS VOLUME CONTROL Turn the VOLUME control on the unit, or press the VOL buttons on the remote control. The vc)lume level is shown on the display for four seconds. It can be adjusted between Oand MAX (50). It flashes when being set over the level 44. The volume level remains memorized even after the power is turned off. However, if the power is turned off when the volume is set to more than 21, it is automatically set to 20 the next time the power is turned on. To adjust the Ieft/right balance of the front speakers Press the BALANCE button to display “L/R OdB. Then press the DOWN or UP button repeatedly within four seconds. Note that the front speakers balance of the 5.1 CH and Dolby Pro Lclgic modes is also changed. To mute the sound temporarily Press the MUTING button (-20 dB). “MUTE ON” appears on the display for four seconds. While muting the sound, the selected function indicator flashes. Press the MtJTING button again to restore the sound. SUPER T-BASS SYSTEM The T-BASS system enhances the realism of low-frequency sound. Press the T-BASS button. Each time it is pressed, the level changes. Selsct om? of “the three levels, or the off position to suit your preference. (cancel) Low-frequency sound may be distorted when the T-BASS system is used for a disc or tape in which low-frequency sound is originally emphasized. In this case, cancel the T-IBASS !system. SOUND ADJUSTMENT DURING RECORDING The output volume and tone of the speakers or headphones may be freely varied without aflecting the level of the recording. ENGLISH ELECTRONIC GRAPHIC EQUALIZER GEQ GEQ MULTIJOG This unit provides the following five different equalization modes. ROCK: Powerful sound emphasizing treble and bass POP: More presence in the vocals and midrange JAZZ: Accented lower frequencies for jazz-type music CLASSIC: Enriched sound with heavy bass and fine treble BGM: Calm tone with suppressed bass and treble Press the GEQ (Graphic Equalizer) button, and turn the MULTI JOG until the desired equalization mode is displayed. The GEQ modes are displayed cyclically as follows. ROCK— PoP— JAZZ — CLASSIC —BGM r 1 ~~ Ml ~ —M3— M2— ,-------Manual mode -------~ The selected mode name is displayed for four seconds, and the aindicator appears on the Ierl side of the selected mode name. Selected mode To cancel the selected mode Press the GEQ button again. “GEQ OFF” appears on the display. To select with the remote control Press the GEQ button repeatedly until the desired equalization mode is displayed. Five preset modes, the manual modes Ml to M4 and “GEQ OFF can be selected. The GEQ system is automatically canceled: -when the Dolby Pro Logic is turned on -when the 5.1 CH function is selected . The GEQ system cannot be turned on while the 5.1 CH function is selected. SETTING NEW EQUALIZATION CURVES Up to 4 equalization curves can be stored as the manual modes Ml to M4. 1 3,6 2 1,5,7 1 Press the GEQ button and press the ENTER button within 4 seconds. 2 Press the DOWN or UP button to select a frequency, The level indicator of the selected frequency flashes. 3 Turn the MULTI JOG to adjust the level of the selected frequency. 4 Repeat steps 2 and 3 to make the desired equalization curve. In steps 2 and 3, the unit returns to normal mode when no operation is made for about 8 seconds. 5 Within 8 seconds, press the ENTER button. “GEQ Ml” appears on the display. 6 Turn the MULTI JOG to select a preset number from Ml to M4. 7 Press the ENTER button. The equalization curve is stored. The selected preset number and the equalization curve are displayed for a few seconds for each. To adjust the GEQ curve temporarily Follow the steps from 1 to 4 above. The adjusted GEQ curve still remains before changing or canceling the GEQ mode. To select the manual preset curve Press the GEQ button, and turn the MULTI JOG until the desired manual preset number is displayed. 9 ENGLISH DSP SURROUND DSP DSP MULTIJOG MANUAL SELECT ( ~o @@ F DOW”N,UP The DSP (Digital Signal Processor) surround circuits can recreate the effect of sounds reflected from walls or ceilings, to obtain the sound Ipresence of real environments. There are four modes with matching graphic equalization modes. Equalization modes are selected automatically and can also be selected or turned off to suit yolur preference. Press the DSP button, and turn the MULTI JOG until the desired DSP mode is displayed. The selected mode name is displayed for four seconds, and the indicators aappear on the left sides of the selected DSP name and matching GE(2 mode name. Selected DSP mode Matching GEQ mode When the music source is monaural Select LIVE to obtain a simulated stereo effect. When DANCE, HALL or ARENA is se...