|
Anleitung Zusammenfassung
it can store a total of 30 signal codes of the external remote control. Use the remote control. 1 Press the LEARN button. “ADDRESS flashes on the display window. 2 Press one of the MEMORY buttons (A-O), then the ADDRESS 1 or 2 button to designate the button on which the signal code is stored. The indication you designated appears on the display. Example: When designating the ADDRESS 1 on the MEMORY A button. 3 Pointing the remote control of the connected equipment toward the unit, press the function button on it to be stored. “LEARN will appear when the signal code is stored. “ERROR may appear if the signal code is not accepted. To stop storing Press the LEARN button. m The signal code of the external remote control may not be received: -When the signal code to be stored is not standard -When a fluorescent lamp lights up near the remote sl?nsor in the display window Some signal codes, for example, those of the VOLUIME UP/ DOWN button, the SEARCH button and the SEND button to transmit the timer recording program may not be memorized correctly. When operating external equipment with the MEMORY and the ADDRESS buttons on which such signal codes are stored, operations may not perform well. When designating a button on which the signal code has already been stored, the previous data is erased. To operate the connected equipment Press one of the MEMORY buttons, and the ADDRES!3 1 or 2 button on which the signal code has been stored. Set the remote control extender so that it points toward (external equipment to be operated. As the remote control extender is not supplied to AV-X100, this function is not available. Using the supplied seals Put the supplied seals on the remote control to identify the buttons and addresses on which the signal codes of external remote controls are stored. It is recommended to store the signal codes in printed order of the seals. If they do not suit your arrangement or operation, use the supplied blank seals. Take the seals off the sheet and put them on the remote control. After two seconds, the display returns to step 1. 4 Repeat steps 2 and 3 to store other signal codes. ENGLISH14 SETTING THE SLEEP TIMER CARE AND MAINTENANCE Occasional care and maintenance of the unit is needed to optimize the performance of your unit. To clean the cabinet Use a soft dry cloth. 1 If the surfaces are extremely dirty, use a soft cloth lightly 2 moistened with mild detergent solution. Do solvents, such as alcohol, benzine or thinner not use strong as these could damage the finish of the unit. The unit can be automatically turned off at a specified time. Use the remote control. 1 2 To check the time remaining until the power turns off Press the SLEEP button once. The remaining time is displayed for four seconds. To cancel the sleep timer Press the SLEEP button twice so that “SLEEP on the display disappears. 15 ENGLISH SPECIFICATIONS FM tuner section Tuning range 87.5 MHz to 108 MHz Usable sensitivity 13.2 dBf (IHF) Antenna terminals 75 ohms (unbalanced) AM tuner section Tuning range 530 kHz to 1710 kHz (1O kHz step), 531 kHz to 1602 kHz (9 kHz step) Usable sensitivity 350 pV/m Antenna Loop antenna Amplifier section Power output [Stereo Mode] Front AV-X200: 120 watts per channel, Min. RMS at 8 ohms, from 40 Hz to 20 kHz, with no more than 0.8% Total Harmonic Distortion AV-XI 00:65 watts per channel, Min. RMS at 8 ohms, from 40 Hz to 20 kHz, with no more than 0.8% Total Harmonic Distortion [Dolby Pro Logic Mode] Front AV-X200: 100 watts per channel, Min. RMS at 8 ohms, from 40 Hz to 20 kHz, with no more than 0.8% Total Harmonic Distortion AV-XI 00:60 watts per channel, Min. RMS at 8 ohms, from 40 Hz to 20 kHz, with no more than 0.8% Total Harmonic Distortion Rear (Surround) AV-X200: 50 watts per channel, Min. RMS at 16 ohms, 1 kHz, with no more than 0.8% Total Harmonic Distortion AV-XI 00:10 watts per channel, Min. RMS at 16 ohms, 1 kHz, with no more than 0.8% Total Harmonic Distortion Center AV-X200: 100 watts, Min. RMS at 8 ohms, 1 kHz, with no more than 0.8% Total Harmonic Distortion AV-XIOO: 60 watts, Min. RMS at 8 ohms, 1 kHz, with no more than 0.80/0 Total Harmonic Distortion Total harmonic AV-X200: 0.07% (105W, 1kHz, 8 distortion ohms, Front) AV-XIOO: 0.06% (40 W, 1 kHz, 8 ohms, Front) Inputs AUDIO IN PHONO: 2.8 mV (50 kohms) CD: 300 mV (50 kohms) TAPE MONITOR: 200 mV (25 kohms) VIDEO 1, VIDEO 2/LD/MD, VIDEO 3, AUXflV: 250 mV (50 kohms) VIDEO IN: 1 Vp-p (75 ohms) outputs AUDIO OUT (REC OUT): 200 mV (2 kohnns) \/lDEO OUT (MONITOR): 1 Vp-p (75 ohms) SUPER WOOFER: :3.1 V (AV-X200)/ 2.19 V (AV-)(100) FRONT SPE:AKERS IMP: 8 Q (front speakers A and B): accepts speakers of 8 ohms or more SURROUND SPEAKERS IMP:16 Q (surround speakers): accepts speakers of 16 ohms or more CENTER SF)EAKEFI IMP: 8 !2: accepts a speaker of 8 ohms or more PHONES (sitereo jack): accepts headphones of 32 ohms or more Muting --20 dB General Power requirements ‘120 V AC, 60 Hz Power consumption AV-X200: 135 W AV-X1OO:115 W Dimension...
Dieses Handbuch ist für folgende Modelle:Receiver und Verstärker - AV-X100 (6.9 mb)