In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. VIBRATION VIBRATION LEVEL 0.02g Vibration levels at the operators handles were measured in the vertical, lateral, and longitudinal directions using calibrated vibration test equipment. Tests were performed on 07/14/94 under the conditions listed: SOUND7 8 Sound tests conducted were in accordance with 2000/14/EEC a

Federal laws apply on federal lands. 21. DO NOT touch hot muffler, cylinder, or fins because contact may cause burns. VIBRATION VIBRATION LEVELS 2.0g Vibration levels at the operators handles were measured in the vertical, lateral, and longitudinal directions using calibrated vibration test equipment. Tests were performed on 11/20/98 under the conditions listed: SOUND 4 5 6 7 0 0 0 0 0 0 SAFETY INSTRUCTIONS GENERAL SAFETY ASSEMBLY LABELS . . . . . . . . . . . . . . . . . . . . OPERATION PARTS DR

49,50,51) 900255 1 800988 1 800988 1 800097 1 800097 1 48 KD PARTS EAG HANDLE ASSY 900475 1 900475 1 - - 900475T 1 - - 49 KEY 9201121 1 9201121 1 9201121 1 9201121 1 9201121 1 50 WASHER LOCK 3/8 TWIST TOOTH 400502 1 400502 1 400502 1 400502 1 400502 1 51 CAPSCREW (HARDENED) 900243 1 900243 1 900243 1 900243 1 900243 1 52 HOUSING ASSY 900257 1 900257 1 900257 1 900257 1 900257 1 53 ENGINE 900244 1 900166 1 900166 1 900166T 1 900166T 1 54 NUT LOCK 5/16-18 8160002 3 8160002 4 8160002 4 81600

KD-50. KD-50C KD-50T, KD-50CT, KD-55CKW OWNER’S MANUAL PART NO. 900183 PAGE 1 OF 4 FORM NO. 122887 PART NO. 9QQ183 FORM NO. 122887 item no. PARTS LIST KD55CKW Part No. QTY KD60C Part No. QTY KD60 Part No. QTY KD60CT Part No. QTY KD60T Part No. QTY 1 EAG FELT (RENTAL 900751) 900650 1 900650 1 900650 1 900650 1 900650 1 2 THROTTLE ASSEMBLY (INC (2) of 4, 5, 11) 900343-01 1 900604 1 900343 1 900514-02 1 900343 1 3 4 LOCKNUT - - - - 8164005 2 8160001 1 8164005 2 5 SCREW - - -

Close zipper before starting engine. 3. TIGHTEN STRAP SECURELY to hold bag on discharge outlet. 4. ATTACH upper bag hanger straps by sliding grommet over rubber stud and on upper handle after handle is locked in place. DUST IS THE GREATEST CAUSE OF LOST VACUUM! SHAKE BAG WELL AFTER EACH EMPTYING. RUN ENGINE AT HALF THROTTLE FOR FIRST HALF HOUR TO CONDITION NEW MAINTENANCE 1. ENGINE: See engine manufacturer instructions. 2. Inspect machine before starting unit. 3. Maximum vacuum: Maintain

Shreds leaves, dramatically reducing total volute. HOSE KITS For vacuuming in hard to reach areas. HeavyDuty Vacuum Hose Kit P/N 900943. 4" (102mm) x 10' (3.05m) Homeowners Vacuum Hose Kit P/N 900942. 4" (102mm) x 1Û' (3.05m) NOZZLE WEAR PLATES P/N 900810. Extends nozzle life when used along curbs and hard surfaces. STANDARD FELT DEBRIS BAG P/N 900803. Standard on KD medals. For dusty ccnditicns. OPTIONAL DEBRIS BAGS TURF DEBRIS BAG P/N 900806 for use in leaves and grass in ron-dusty c

Nozzle height ^ too high or too low . Hbæ lot cap missing. Clcggæl nozzle or œhaust. Excessive quantity of debris. Clean d^>ris bag. Shake bag clean or wash. Adjust nozzle height. Check for hose kit cap. Unclog nozzle or œhaust (see page 5). Allow air to fœl with o^ris. Abnormal vibration. Loose or out of balance impeller or loose ^gine. Check impeller and replace if ræuiræL Check Engine. Engine will rot s^art. Stop aitch off (tinea only). Throttle in off position. Engine not in full choke pos

directions using calibrate vibration te^. ^pipn^t. Tests were performs! on 05/03/94 under the conditions listed: GENERAL CONDI- _partly Cloudy_ TION:_ TEMPERATURE: WIND SPEED: WIND DIRECTION: HUMIDITY: 60 * F (15.5 C) 5 MPH (8kmh) BAROMETRIC PRESSURE :29.8’’ (757mm Hg) Form No. F021695C 70 70 TABLE OF CONTENTS SAFETY INSTRUCTIONS 2 GENERAL SAFETY . . . . 3 ASSEMBLY....... 3 PARTS BAG & CONTROLS 4 LABELS ........ 4 OPERATION 5 PARTS DRAWING & LIST 7 6 MAINTENANCE 8 TROUBLESHOO

Do not kink, stretch, or break control cables, control housings, or end fittings while removing handles. 4.Invert and support machine with engine not touching ground to prevent damage to recoil starter. 5.Disassemble housing by removing six (6) lock nuts and washers from nozzle frame, (2 are inside of nozzle opening). 6.Remove impeller bolt and lock washer. 7.Lift impeller upward. If impeller slides freely, proceed to (step 10). 8 .Place two crowbars between impeller and housing on opposite

ASSY. ( INCL. 17, 37, 38, 45 ) 900749 1 900749 1 900749 1 34 WHEEL ASS’Y (INCLUDE 21) 900509 4 900509 4 900509 4 35 WASHER 0.75 “C” 900997 0-1 900997 0-1 900997 0-1 36 37 SCREW CAP 5/16-18 X 1” *8041028 2 *8041028 2 *8041028 2 38 SPACER 0.340” I. D. X 0.330” LG. 900745 2 900745 2 900745 2 39 PLATE - BRACE REAR 900905 2 900905 2 900905 2 40 SCREW CAP 1/4-20 X 1/2 *8041002 4 *8041002 4 *8041002 4 41 SPACER 900926 6 900926 6 900926 6 42 SCREW, SELF TAPPING 10 - 24 NC X 1/2 LG. *8123