Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Stainless steel wool can possibly be used, but only in the grinding direction. O Never use chloric products (bleaching dye, hydrogen chloride etc.) for cleaning chrome nickel steel, even if they are diluted. O Never use corrosive substances for cleaning the floor under the appliance (e.g. hydrochloric acid). Clean the appliance with commercial cleaning agents. Do not use granular or abrasive agents. 3.1 GAS BURNER So far as is necessary, the pilot burner and main burner are cleaned by after-sales service. 3.2 FLAME In a visual check, the flames must be dark blue without any upper yellow or orange tips; they must be stable and soot-free and adhere firmly to the outlets. If there is a lack of primary air, the flame has yellow streaks and tips; if there is too much primary air, the flame is short, transparent and tends to lift off the burner. When the flame is correctly adjusted, it must not lift off or backfire when the burner is cold as well as warm. The flame will backfire into the inside of the burner when the speed of the gas-air mixture through the burner outlets is too low, particularly when the air passages are dirty. The different ignition processes must also take place without any delays. This concerns: ignition, arc-through and. extending the flame over the whole burner area. If the flame fails to meet all the requirements, cleaning or maintenance is necessary. 4. MALFUNCTION Malfunction Possible cause Remedy Plate does not heat up. • The thermal limiter has tripped. • Defective thermostat. • The capillary tube sensor is damaged. - Inform After-sales service. Flame smokes. • Gas mix too rich. • Partially blocked burner gaps. - Inform Customer Service. Long yellow flame tips. • Mixing tube narrowed by dirt. - Inform Customer Service. Flame lifts off. • Exit velocity too high due to blocked burner gaps. • Pressure regulator on gas cylinder not operating correctly. - Inform Customer Service. Flame flashes back. • Mixture too lean. • Insufficient exit velocity at burner gaps. • Soiled airways • Blocked nozzle. - Inform Customer Service. No flame or flame too small. • Blocked nozzle or mixer tube. • Blocked gas tap. • No gas. • Insufficient gas pressure. - Inform Customer Service. - Check gas tap setting. No flame at low setting. • Blocked low setting nozzle. - Inform Customer Service. Pilot burner No flame. • Blocked burner gaps. • Blocked nozzle. - Clean pilot burner cap. Flame goes out after control valve release. • Thermo-element insufficiently heated (dirty?) • Defective thermo-element - Inform Customer Service. Flame too small or too large. • Primary air ratio adjusted. • Nozzle blocked. - Inform Customer Service. Seite 10 62.9677.01 UL OPERATING INSTRUCTIONS EH Electrolux 5. STORAGE SPACE The storage space (Fig.10) is incorporated into the base unit. Recommended accessories: - Shelf holder (1) 2 off. - Shelves (2) 1 off. 1 Shelf holder 2 Shelves Fig.10 Storage space 62.9677.01 UL Seite 11 0] Electrolux OPERATING INSTRUCTIONS Seite 12 62.9677.01 UL INSTRUCTIONS GÉNÉRALES H Electrolux I . INSTRUCTIONS GÉNÉRALES 1. CONSIGNES DE SÉCURITÉ ET D'UTILISATION 1.1 INSTALLATION ET MISE EN SERVICE Le montage, le réglage et la première mise en service de l'appareil doivent s'effectuer conformément aux instructions du fabricant et être confiés exclusive...
Dieses Handbuch ist für folgende Modelle:Andere Küchengeräte - WHGUSAOOOO 9CHG584123 (877.51 kb)
Andere Küchengeräte - Thermaline 9CHG584123 (877.51 kb)
Andere Küchengeräte - Thermaline 9CHG584122 (877.51 kb)
Andere Küchengeräte - Thermaline 9CHG584124 (877.51 kb)