(California Health & Safety Code 25249.5 et seq.) Preparing the Soldering Tip 1. Using Wrench (16), check that the Soldering Tip Nuts (2) are not loose. Do not overtighten as you may strip the threads. 2. Set the Soldering Gun on the workbench, and plug the Line Cord into an electrical outlet. 3. Press on the Trigger Switch (12) until the Soldering Tip (1) heats up. 4. Apply a sufficient amount of rosin-core solder to melt over the entire tip of the Soldering Gun. Wipe the tip with a rag until t

. Do not install unit near flammables. . Do not overload building wiring . be sure power supply system is properly sized, rated, and protected to handle this unit. STATIC (ESD) can damage PC boards. . Put on grounded wrist strap BEFORE handling boards or parts. . Use proper static-proof bags and boxes to store, move, or ship PC boards. H.F. RADIATION can cause interference. . High frequency (H.F.) can interfere with radio navigation, safety services, computers, and communicationsequipment. . Hav

IN MOST CASES, A BLACK & DECKERREPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER. SAVE THIS MANUAL FOR FUTURE REFERENCE. VEA EL ESPANOL EN LA CONTRAPORTADA. POUR LE FRANCAIS, VOIR LA COUVERTURE ARRIERE. INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO YPOLIZA DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. Welcome to the Wonderful World of Black & Decker Craft Products. Yo

Be sure that the soldering ip has been freshly tinned. When you press the switch button, the work light will come on and the tip will start heating immediately. In about 6 seconds, with light pressure, toucfi the tip to the connection, and at the same time, feed the solder to the spot being heated by the tip. After enough solder melts to just cover the connection, release the button, lift the tip and ailow solder to cool. Do not disturb the connection until solder has hardened. Pencil can be pl

However, after several charge and discharge cycles, the battery will be back up to its full capacity. 3. While charging, the Charger may hum and become warm to touch. This is a normal condition* and does not indicate a problem. 4. If the battery does not charge properly—(!) check power supply at receptacle by plugging in a lamp or other appliance, (2) check to see if receptacle is connected to a light switch which turns power of when you turn out the lights, 5. Whenever you unplug the Charger

It will solder from 35 to 100 joints per charge, depending upon type of application. A finger-tip ON-OFF button is provided for safety and convenience. For operational safety and proper use of the Soldering Pencil, please read all safety rules and instructions. Don’t forget to send in the guarantee registration card. THANK YOU FOR BUYING BLACK & DECKER! SOLDERING PENCIL SAFETY RULES 1. WHEN NOT IN USE, store the tool in a dry, high or locked-up place — out of the reach of children. 2. KEEP

9. Always allow sufficient time for the Blow Torch to completely cool down before storing. Do not store flammable liquids or materials in the area surrounding the Blow Torch. 10. Maintain labels and nameplates on the Blow Torch. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. SKU 91061 PAGE 4 11. Never use gasoline, kerosene, or other highly volatile fluids as a starter as they can explode. 12. Dress safely. Do not wear loose clothing

MINI-IRON - Use for iron-ons, fusible webbing and tapes, applique quilting, 3 632901-00 Iron 10/24/05 12:37 PM Page 4 Assembly 21 Tip Storage A handy storage bin is built-in to the Craft Iron. Insert the coiled spring support into the Craft Iron To remove the bin from the base of the unit, ( figure 1) base by aligning the protrusions on the press in on the sides and pull out as shown in support with the slots in the opening. Push the figure 4. support straight in until it “clicks” into place. WA

Phileas Foggstraat 16 7821 AK Emmen Drenthe The Netherlands Phone: (0591) 66 75 00 Fax: (0591) 66 75 95 BP860 Kabelloses batteriebetriebenes Lotwerkzeug Vielen Dank, dass Sie sich fur das batteriebetriebene kabellose Lotwerkzeug BP860 von Weller entschieden haben. Dies ist das neueste Produkt aus der Serie Lot- und Hei.luftwerkzeugen mit und ohne Kabel; von Weller - dem weltweit fuhrenden Hersteller von Lotprodukten. Bei richtiger Pflege wird Ihnen Ihr BP860 uber viele Jahre zuverlassige Dienste

• The charger is not intended for any use other than charging the exact type of rechargeable battery pack as supplied with the charger. Any other use may result in the risk of fire, electric shock or electrocution. • The charger and battery packs supplied with it are specifically designed to work together. Do not attempt to charge the battery pack with any other charger than the one supplied. • Do not place any object on top of the charger as it could cause overheating. Do not place the charger