Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
IN MOST CASES, A BLACK & DECKERREPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER. SAVE THIS MANUAL FOR FUTURE REFERENCE. VEA EL ESPANOL EN LA CONTRAPORTADA. POUR LE FRANCAIS, VOIR LA COUVERTURE ARRIERE. INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO YPOLIZA DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. Welcome to the Wonderful World of Black & Decker Craft Products. Your new Dual Temp Craft / Soldering Iron is designed to apply two different temperature settings to almost any surface using a variety of different tips. You’ll find dozens of uses in the workshop and around the house for this versatile tool. For personal safety and for proper operation of your Craft Iron, take the time to carefully read and understand all of the safety and instructions in this booklet. Thank you for selecting Black & Decker! 1 632901-00 Iron 10/24/05 12:37 PM Page 2 IMPORTANT SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/orserious personal injury. SAVE THESE INSTRUCTIONS WARNING: When using Electric Tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, andpersonal injury, including the following: 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don’t expose powertools to rain. Don’t use power tools in damp or wet locations. Keep work area well lit. 3. KEEP CHILDREN AWAY. All visitors should be kept away from work area. Do not let visitors contact tool or extension cord. Supervise the use of this tool by children. 4. STORE IDLE TOOLS. When not in use, tools should be stored in dry, high or locked-up place — out of reach of children. 5. USE SAFETY GLASSES. 6. DON’T ABUSE CORD. Never carry tool by cord or yank it todisconnect from receptacle. Keep cord from heat, oil, and sharp edges. 7. DON’T OVERREACH. Keep proper footing and balance at all times. 8. DISCONNECT TOOLS. When not in use, before servicing and when changing accessories. 9. This tool is recommended for indoor use only 10. STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired. 11. DO NOT TOUCH THE HEATED TIP OF THE TOOL OR THE HOT MELTED SOLDER. The operating temperature of this tool isapproximately 900°F on the HIGH (II) setting and 500° on the LOW (I) setting. 12. Never attempt to use any material other than that recommended in this manual. 13. Keep your craft iron well away from all flammable material. 14. To avoid burns, always assume that the tip is hot and return the craft iron to its protective stand. 15. Never leave your tool plugged in and unattended. After use, unplug tool, allow the tip to cool and store in a safe place. 16. Before making any adjustment (removing or replacing a tip, etc.) make sure the tool is unplugged and cool. 17. Always work in a well ventilated area. 18. Do not dip the tool into a liquid. WARNING: This product contains chemicals, including lead, known to the state of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. This also applies tolead based solders. Extension Cords An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of performance. The smaller the gauge number of the wire, the greater the capacity of the cable; that is, 16gauge has more capacity than 18 gauge. When using more than one extension cord to make up the total length, be sure each individual extension contains at least the minimum wire size. Before using anextension cord, inspect it for loose or exposed wires, damaged insulation and defective fittings. Make any needed repairs or replace the cord if necessary. To determine the minimum size required, refer to the chartbelow: Minimum Gage for Cord SetsVolts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300 Ampere RatingMore Not more American Wire GageThan Than 0 - 6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended Polarized Plug This appliance has a polarized plug (one blade is wider than theother ). To reduce the risk of electric shock, this plug is intended to fitinto a polarized outlet only one way. If the plug does not fit fully intothe outlet, reverse the plug. If it still does not fit, contact a qualifiedelectrician. Do not modify the plug in any way. SAVE THESE SAFETY RULES FOR FUTURE USE 2 632901-00 Iron 10/24/05 12:37 PM Page 3 Use your Craft Iron for a variety of applications including Woodburning, Soldering, Scrapbooking and Image Transfer. Use your Dual Temp Craft Iron to decorate and personalize a variety of different materials. Hi temperature (II) for wood, leather, gourds, heavy weight paper, paper mache, wicker-rattan and heavy plastics. Low (I) for lighter pap...
Dieses Handbuch ist für folgende Modelle:Lötlampen - CI500 (279.52 kb)