Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
A dash (-) means that no patch memory is selected. When you store a Scene, the last recalled or stored Input Patch and Output Patch library memories are automatically linked to that Scene. If the specified Input or Output Patch library memory contains no data, only the Scene is recalled, the input and output patching will remain the same. Bass Management for 3-1 & ST Monitor Matrixes Bass Management can now be used with the 3-1 and Stereo Out monitor matrixes. Previously, Bass Management could be used only with the 5.1 monitor matrix. The Bass Management function can be found on the Surround Monitor Setup page, which can be located by using the MONITOR [DISPLAY] button when either the 3-1 or 5.1 Surround mode is selected. The following screen shots show the Bass Management configurations for the 5.1, 3-1, and Stereo monitor matrixes, with Bass Management turned on and off. Note: When using the 3-1 monitor matrix, even with film sources, use Bass Management presets 1 and 2 (presets 3 and 4 may not provide correct monitoring). In addition, the Monitor Matrix configurations have changed as follows. (The 5.1 to 5.1 matrix is unchanged.) 5.1 to ST IMONITOR MflTRI XI З-1 to З-1 IMONITOR MflTR1XI s -Ешь— ATT1 ; e ; -Ls -Rs 5.1 to 5.1 З-1 to ST |MO N 1 TOR MflTR1XI AT -JHfjrfe] тз! 1 fiTT£ ЙТТЗ 0 : : 0 : : 0 : 5.1 to З-1 & 1 DAW Control Regardless of Layer Selection Previously, the transport controls, locator, track arming functions, and shuttle and scrub could be used to control an external DAW only when a Remote Layer was selected. With the new DAW CONTROL option, a DAW can be controlled regardless of which Layer is currently selected. The new MACHINE CONTROL and DAW CONTROL options have been added to the following five pages: Machine Configuration and Locate Memory, which are selected by using the LOCATOR [DISPLAY] button, and Track Arming Group, MTR Track Arming Configuration, and Master Track Arming Configuration, which are selected by using the TRACK ARMING [DISPLAY] button. When the MACHINE CONTROL option is on, external MMC/P2 machines can be controlled, except when a DAW Remote layer is selected, in which case the DAW is controlled. When the DAW CONTROL option is on, the DAW can be controlled regardless of which Layer is currently selected. 0 Initial Data TRACK ARM tHS1CH23-CH23 :track armimg group:| ONTROL |0|MRCHINE CONTROL □ DRW C IGF!QUP sl mm IDBDBBBB [3|i0]|TT]|i2]|i3|w]|i5]|i6] 0 a 0 a a @ @ s IGF!QUP Bl tom nBHnaaaa a a a a a a a a IGF!QUP 1=1 mm □ smiiissQE] [3|i0]|TT]|i2]a|w]|i5]|i6] aaaassss IGRQUP 01 row □ [£][I][l|[I][l|[3[I] a a □ a a a a a 1 0B„ ™ M MTP M , 2 Dimmer & Talkback Control via the CONTROL Port The Control Room and Surround Monitor Dimmers, and the Talkback function can now be controlled remotely via the CONTROL port. CONTROL fr^l Í OOOOOOOOOOOOO ) rol V OQQQQOQQQOOO J Each time the GPI0 input (pin 22) goes Low (ground), Talkback is turned on or off. Each time the GPI1 input (pin 10) goes Low (ground), the Dimmer is turned on or off. Solo to Studio Out With the new Solo Bus to Studio Out preference on the Preferences 1 page, which can be selected by using the DISPLAY ACCESS [SETUP] button, soloed channels can now be monitored through the STUDIO MONITOR OUT. ~B Initial Data M13^ >SETUP m:1CH24-CH24 0 ñuto ROUTING Display □ L/R Nominal Pan □ Ruto PHASE/INSERT DisplayDFast Meter Fall Time 0 ñuto DELñV Display 0 TC Drop Warning □ ñuto AUX/MfiTR I X Display 0DIO Warning 0 ñuto DVNñMICS Display 0MIDI Warning 0 ñuto PAN/SURROUND DisplayD Initial Data Nominal 0 ñuto EQUALIZER Display 0 Meter Follow Layer □ ñuto SOLO Display □ Scene MEM ñuto Update □ñuto WORD CLOCK Display 0 Joystick ñuto Grab 0 ñuto Channel Select 0 Cascade COMM Link 0 Store Confirmation DSolo Bus to Studio Out Hm PREFERI j& PREFER2 PREFER3 jS MIDI ! HOST ^ frT When the Solo Bus to Studio Out preference is on, and all the STUDIO signal source buttons in the MONITOR section are off (i.e., [CONTROL ROOM], [STEREO], [AUX 11], and [AUX 12]), the Solo signal is output by the STUDIO MONITOR OUT when channels are soloed. User Defined Keys The following items have been added to the list of functions that can be assigned to the USER DEFINED KEYS. # Function Display 161 Surr Lib. Recall +1 Surr Lib+1 RCL 162 Surr Lib. Recall -1 Surr Lib-1 RCL 163 Surr Lib. Recall No. XX Surr LibXX RCL Functions are assigned to the USER DEFINED KEYS on the USER DEFINED KEY ASSIGN page, which is selected by using the USER DEFINED KEYS [DISPLAY] button. In addition, the following initial assignments of USER DEFINED KEYS Bank A have changed. # Bank A # Bank A 1 SOLO ON —> 1 Surr Lib 0 RCL 2 No Assign —> 2 Surr Lib -1 RCL 3 No Assign —> 3 Surr Lib +1 RCL 3 M.D....