78008. 1/0. Phone: +1 (214) 421-7366 Fax: +1 (214) 565-0976 Toll Free: +1 (800) 441-1601 BevLes Website: 729 Third Avenue E-mail: sales@BevLes.com Dallas, TX 75226 1 TABLE OF CONTENTS 1 2 3 4 5 6 7 2-1 2-2 2-3 2-4 2-5 3-1 3-2 4-1 4-2 4-3 4-4 5-1 5-2 6-1 6-1a 6-1b 6-1c 6-1d 6-1e 6-1f 6-1g 6-1h 6-1i 6-1j 6-1k 6-1l 6-1m 6-1n 6-1o 7-1 7-2 7-3 7-4 7-5 7-6 8-1a 8-1b WARRANTY 3 GETTING STARTED 4 INTRODUCTION 4 MODELS 4 UNPACKING 4 SETTING-UP 5 CLEANING. 5 OPERATION 6 OPERATING CONTROLS AND COMPONENTS 6

liabilit. relatin. t. th. continue. us. o. th. product. . Exclusio. o. consequentia. an. incidenta. damages-I. n. even. shal. Bevle. b. liabl. fo. an. incidental. special. indirect. o. consequentia. damages. whethe. resultin. fro. non-deliver. o. fro. th. use. misuse. o. inabilit. t. us. th. product. o. fro. defect. i. th. product. o. fro. Bevles. ow. negligenc. o. othe. tort. Thi. exclusio. applie. regardles. o. whethe. suc. damage. ar. sough. fo. breac. o. warranty. breac. o. contract. neglige

**WARNING: A clearance of at least four (4) inches is required between the top of full size units (models beginning with CA70) and any other equipment or surfaces to allow air to circulate to the motor air vents. Do not set anything on top of these units. Proper operation of the unit requires that it be level and that it be plugged into a separate electrical line protected by a fuse or circuit breaker of the proper rating. CA70-CV16 120V/1500W/14.3A CA43-CV7 120V/1500W/14.3A CA70-CV16HW 120V/200

Power Switch 2. Power Switch Indicator lamp 3. Thermostat 4. Thermostat Indicator Lamp 5. Thermometer 3-2 OPERATIONAL PROCEDURES 1. Plug unit into wall. CAUTION: Check the serial number label located on the right side of the cabinet (as you are facing the front of the unit) at the top to be sure that your unit is compatible with your electrical supply. See section 4-4 for more information. Figure 6 2. If humidity is desired, fill water pan % full of water and adjust baffles. (Fig. 7) 2a. For max

5-1 TROUBLESHOOTING To determine the cause of any malfunction: 1. Determine the problem (e.g., the food isn't staying hot). 2. Locate the problem in the Troubleshooting table. 3. Read through the possible causes ,then try each solution listed until the problem is resolved. . 4. If you are unable to locate the problem in the table or if the solutions listed don't work, please call the BEVLES manufacturing facilities for assistance at (800) 441-1601. You will need to provide the factory personnel

2. Gently lift off the front panel while guiding attached wires and thermometer probe to prevent damage. (Fig. 9) 3. Leaving wires attached, gently place front panel face down on a clean work space. (Fig. 10) 4. To replace front cover, reinsert thermometer probe into receptacle, guide wires back into place and reattach panel with the five phillips head screws. Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 6-1c. Replacing the power indicator lamp module. Required: Wiring markers (colo

(Fig. 16) 3. Remove the nut, washer and retaining bracket and pull thermometer out the front of the panel. 4. Replace retaining bracket and insert new thermometer into opening. **NOTE: Align thermometer so that the 150° reading will be straight up when the front panel is replaced and the heating module is flipped over. (Fig. 17) 5. Replace and tighten washer and nut on rear of front panel. DO NOT OVER TIGHTEN! 6. Replace the front panel (section 6-1b). 6-1g. Replacing the power cord for a CA70 u

Tighten screws to secure power cord into connector. *"WARNING: Replace only with a BEVLES power cord properly rated for your unit. 8. Insert new wires through opening in back panel and reattach elbow connector. 9. Reattach green ground wire to back panel. 10. Reconnect power cord wires using wire nuts and wiring diagram. Retape over wire nuts and wires. (Diagram 3) **WARNING: Severe damage can be caused to your unit by improperly connecting wires. 11. Replace the back panel using the five philli

(Fig. 41) 4. Mark all the wires connected to the fan blower motor(s) with a color code or number to make proper re-connection easy. (Fig. 42) 5. Remove wire nuts and set cover aside. 6. For CA70 units, remove the two screws securing the clips that attach the copper thermostat probe to the fan blower. Use a medium flathead screwdriver. Free the copper probe and carefully set out of the way. (Fig. 43) **NOTE: DO NOT kink or bend copper tubing or probe. Remove four screws (two at each end) that hol

Remove thermostat dial from front panel by rotating the dial to expose the set screw and reversing the sat screw with a small flathead screwdriver. (Fig. 34) 4. Remove the two screws holding the bezel (chrome ring) behind the thermostat dial with a medium (6”) phillips screwdriver. Carefully pull thermostat away from the rear of the front cover. 5. Remove the fan blower motor assembly cover (on the left side of module as you are facing the front panel) by removing the two front and two rear scre