Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Bakers Pride Oven Dateigröße: 1.57 mb Dateiname: Unterrichtssprache:

(Fig. 41) 4. Mark all the wires connected to the fan blower motor(s) with a color code or number to make proper re-connection easy. (Fig. 42) 5. Remove wire nuts and set cover aside. 6. For CA70 units, remove the two screws securing the clips that attach the copper thermostat probe to the fan blower. Use a medium flathead screwdriver. Free the copper probe and carefully set out of the way. (Fig. 43) **NOTE: DO NOT kink or bend copper tubing or probe. Remove four screws (two at each end) that hold the fan blower motor bracket in place. Use a medium flathead screwdriver. 7. For CA43 units, remove four screws (two at each end) that hold the fan blower motor bracket in place. Use a medium flathead screwdriver. Gently lift bracket to expose mounting clips for the copper thermostat probe. Remove the two screws securing the clips holding the copper thermostat probe with medium flathead screwdriver. Free copper probe and carefully set out of the way. (Figs. 44 &45) **NOTE: DO NOT kink or bend copper tubing or probe. 8. Remove fan blower motor bracket with fan blower motor(s) still attached and place entire assembly on a clean work space. (Fig. 46) 9. Remove fan blower motor(s) from mounting bracket by removing four securing screws with a medium (6”) flathead screwdriver. 10. Mount new motor(s) in same position with the four phillips screws. **NOTE: All replacement motors will have two drilled holes in the blower portion -these are irrelevant unless you are replacing the front motor on a CA70 and will not affect performance in any application. 11. Replace the fan blower motor bracket in heating module with large flange up. (Fig. 46) . Figure 43 Figure 44 Figure 45 1. Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 12. For CA70 units, secure fan blower motor bracket with the four phillips screws. Reattach thermostat probe clips with two flathead screws. **NOTE: DO NOT kink or bend the copper probe or tubing. 13. For CA43 units, reattach thermostat probe clips with two flathead screws. **NOTE: DO NOT kink or bend the copper probe or tubing. Secure fan blower motor bracket with the four flathead screws. 14. Reconnect existing wires to new motor wires. It is not important which new wire is matched with which existing wire group. Re-tape over wire nuts and wires. 15. Replace fan blower motor housing cover, carefully guiding the wires to prevent damage. 16. Replace fan blower motor assembly cover with two front and two rear flathead screws. 17. Replace top mounted heating module (section 6-1 a). 6-1l. Replacing heating element. Required: Medium (6") flathead screwdriver, Medium (6") phillips screwdriver, Crescent wrench, General Electric 1209 caulking 1. Remove top mounted heating module as found in section 6-1a. 2. Remove four screws that secure the air deflector housing (on your right as you are facing the front of heating module) to the module with a medium (6”) flathead screwdriver.(Fig. 47) 3. Gently lift the air deflector housing to access the nuts connecting wires to the heating element. Remove those nuts and washers to free the wires. (Fig. 48) 4. Remove air deflector housing" and place on a clean work area. 5. Remove four screws securing the heating element brackets to the ceramic insulators with a medium (6") flathead screwdriver. (Fig. 49) 6. Slide brackets off the old element and discard the old element. 7. Slide brackets (large one first) over the connector end of the new heating element. (Fig. 50) 8. Reconnect heating element brackets to the ceramic insulators with the four phillips screws. Do not over tighten. 9. Return air deflector housing to the heating module and reconnect wiring (it is not important which way you match the wires to the new element). (Fig. 51) 10. Caulk openings where the heating element enters the air deflector housing with GE 1209 caulking. (Fig. 52) 11. Reconnect air deflector housing to heating module with the four flathead screws. 12. Replace top mounted heating module (section 6-1a). Figure 51 17 Figure 52 6-1m. Replacing the High-temperature s...

Herunterladen

Geben Sie zwei Ziffern: