Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Bakers Pride Oven Dateigröße: 1.57 mb Dateiname: Unterrichtssprache:

**WARNING: A clearance of at least four (4) inches is required between the top of full size units (models beginning with CA70) and any other equipment or surfaces to allow air to circulate to the motor air vents. Do not set anything on top of these units. Proper operation of the unit requires that it be level and that it be plugged into a separate electrical line protected by a fuse or circuit breaker of the proper rating. CA70-CV16 120V/1500W/14.3A CA43-CV7 120V/1500W/14.3A CA70-CV16HW 120V/2000W/18.5A CA43-CV7HW 120V/2000W/17.0A CA70-CV32 120V/1500W/14.3A CA43-CV13 120V/1500W/14.3A CA70-CV32HW 120V/2000W/18.5A CA43-CV13HW 120V/2000W/17.0A CA70-CVMP12 120V/2000WI18.5A CA43-CVMP6 120V/2000W/17.0A CA70-CVMP15 120V/2000W/18.5A CA43-CVMP7 120V/2000W/17.0A WARNING: Plug your unit only .into a grounded receptacle of the correct voltage. Check the serial number label located in the top right front corner on the right side of the cabinet to determine your unit's electrical rating. 2-5 CLEANING **NOTE: Never use steel wool or caustic cleaning compounds on your BEVLES holding cabinet. Cleaning Steps: 1. Push power switch to the OFF position. 2. Unplug power cord from wall. CAUTION:Always unplug the unit before dismantling or cleaning. 3. Remove front and back doors by lifting entire door and sliding hinge off of hinge pins. (Fig. 1) **NOTE: Avoid motions other than straight up or down when removing and replacing doors so as not to damage hinges. 4. Slide out stainless steel water pan containing the three "U" shaped baffles. 5. Lift off the heating module from the top of the cabinet. (Fig.2) **NOTE: At least two people should do the lifting to avoid possible injury. 6. Remove all trays. 7. Remove tray supports by carefully lifting each panel and tilting the bottom toward the center of the cabinet. (Fig. 3) **NOTE: Handle the support panels carefully as any damage or bending will make reinstallation very difficult 8. Remove positive door latches (Fig. 4): 8a. Firmly hold the latch plate against the edge of the door and pull the black capped pin up and out. Figure 4 8b. Slowly pull the latch plate away from the door, ready to catch the flat metal spring as it releases. 9. Models equipped with dutch doors will also have a removable wiper blade attached to the top of the bottom door. To remove this, loosen the two black knurled knobs at either end of the wiper blade retainer. Lift off the stainless steel retainer and the wiper blade. Figure 1 Figure 2 Figure 3 . 10. Clean all pieces thoroughly and carefully with soapy water and soft cloths. **NOTE: Neverusesteelwoolorcausticcleaningcompounds. **CAUTION: Avoid splashing water or any other liquid into the heating module to prevent possible damage to electrical components. Reassembly Steps: 1. Replace door latches (Fig.5): 1a. Wrap the flat metal latch spring lip around the front edge of the door between the two latch butts. 1b. Place the latch plate with the flat side out over the flat metal latch spring and press firmly in place. 1c. Guide the black capped pin down through the top latch butt, the latch plate and bottom latch butt. This will require positive pressure on the latch plate to compress the spring. 2. Replace dutch door wiper blade if your model is equipped with one. Simply slide the gasket and retainer onto the top edge of the bottom door and re-tighten the two black knurled knobs. 3. Carefully replace top mounted heating module and align with top tray supports. 4. Replace tray support panels. 5. Replace doors by sliding door hinges back down onto the hinge pins. 6. You are now ready to operate your unit in accordance with the procedures outlined in section 3-2. 3. OPERATION BEVLES Heated Holding Cabinets are not intended for any use other than as foodservice equipment. Always operate your unit in accordance with the Operational Procedures listed in section 3-2 of this manual. Figure 5 3.1 OPERATING CONTROLSAND COMPONENTS (Fig. 6) 1. Power Switch 2. Power Switch Indicator lamp 3. Thermostat 4. Thermostat Indicator Lamp 5. Thermometer 3-2 OPERATIONAL PROCEDURES 1. Plug unit in...

Herunterladen

Geben Sie zwei Ziffern: