Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Bakers Pride Oven Dateigröße: 1.57 mb Dateiname: Unterrichtssprache:

Remove those nuts and washers to free the wires. (Fig. 48) 4. Remove air deflector housing" and place on a clean work area. 5. Remove four screws securing the heating element brackets to the ceramic insulators with a medium (6") flathead screwdriver. (Fig. 49) 6. Slide brackets off the old element and discard the old element. 7. Slide brackets (large one first) over the connector end of the new heating element. (Fig. 50) 8. Reconnect heating element brackets to the ceramic insulators with the four phillips screws. Do not over tighten. 9. Return air deflector housing to the heating module and reconnect wiring (it is not important which way you match the wires to the new element). (Fig. 51) 10. Caulk openings where the heating element enters the air deflector housing with GE 1209 caulking. (Fig. 52) 11. Reconnect air deflector housing to heating module with the four flathead screws. 12. Replace top mounted heating module (section 6-1a). Figure 51 17 Figure 52 6-1m. Replacing the High-temperature safety thermostat. Figure 53 Figure 54 Figure 55 Figure 56 Figure 57 Required: Medium (6”) flathead screwdriver, Medium (6") phillips screwdriver, Crescent wrench 1. Remove top mounted heating module as found in section 6-1a. 2. Remove four screws that secure the air deflector housing (on your right as you are facing the front of heating module) to the module with a medium (6”) flathead screwdriver. 3. Gently lift the air deflector housing to access the nuts and connecting wires to the high temperature safety thermostat. Remove those nuts and washers to free the wires and the thermostat. 4. Attach the new high-temperature thermostat and reconnect the new wires. 5. Reconnect air deflector housing to heating module with the four flathead screws. 6. Replace top mounted heating module (section 6-1 a). 6-1 n. Replacing the top mounted heating module seal (gasket). Required: Razor blade, General Electric 1209 caulking 1. Remove top mounted heating module as found in section 6-1a. 2. Razor blade old gasket and foam tape off of the heating module. (Fig. 53) **NOTE: Remove all caulking and material carefully. A good seal requires a clean surface. 3. Set new gasket into place using double-face foam tape (included with new gasket) to attach new gasket to module. (Fig. 54) 4. Caulk inner and outer edges of new gasket with GE 1209 caulking. Allow caulking to dry for at least 45 minutes. (Fig. 55) 5. Replace top mounted heating module (section 6-1a). 6.1o. Replacing the fan blower cooling fan for CA43 units. Required: Medium (6”) flathead screwdriver, Medium (6”) phillips screwdriver, Wiring markers (color or number codes), Electrical tape 1. Remove the back panel of the module by removing the five flathead screws and gently removing the back panel. Lay the panel on a clean work surface. 2. Remove four screws inside the back panel that secure the cooling fan to the back panel with a medium (6”) flathead screwdriver. Save spacers for reuse. (Fig. 56) 3. Mark all the wires connected to the cooling fan with a color code or number to make proper re-connection easy. (Fig. 57) 4. Remove wire nuts and retain wire sleeve for reuse. Discard old cooling fan (if under warranty and requested by BEVLES, send fan and Return MaterialAuthorization form to the factory for credit). 5. Slip reserved wire sleeve onto the wires of the new cooling fan. 6. Connect new cooling fan wires to existing wires. It is not important which way you match the new wires. 7. Carefully insert nylon spacers between the cooling fan and back panel. Connect new fan to the back panel with the four flathead screws. (Fig. 56) 8. Replace back panel with the five flathead screws. 9. Replace top mounted heating module (section 6-1a). 1. 7. REPLACEMENT PARTS Use only BEVLES replacement parts in repairing your unit. This assures you of continued high quality performance. 7-1 HOW TO ORDER To determine the parts you need: 1. Use the drawings found in section 7-5 and refer to the parts list in section 7-6 to determine the BEVLES part numbers you need. 2. Note the model number, serial number and the...

Herunterladen

Geben Sie zwei Ziffern: