Handle carriers carefully so they may be re-used. 3. insert the folded edge of the carrier STRAIGHT into the front of the laminator until you feel the rollers grab the carrier. 4. Remove the carrier from the rear of the GBC DocuSeal 120 after it has stopped moving. Leave the pouch within the carrier for a few seconds to cool before removing it. Removing it too soon may distort the lamination. 5. When you are finished laminating for the day switch the machine to “OFF”. ELECTRICAL SAFEGUARDS

5. Insert the carrier and its contents straight into the machine, leading with the folded edge. handle carriers carefully so that they can be reused. REV Selecting Functions} } Control Panel LCD 13 Pro Operating Instructions PRE/H Stand-by 6 The laminated item will automatically exit the rear of the pouch laminator. After the pouch has stopped moving, place the carrier on a flat surface to cool briefly before removing the finished pouch. 7. If the laminated product looks hazy, then the temperatu

Remove 4 book supports from storage compartment, lb. Insert support #1 firmly in front slot. Firmly insert remaining supports in consecutive numerical order. 2a. Plug in and switch on 250T. The yellow wait light will illuminate. 2b. In about 4 minutes a "beep" will sound and the green light will iluminate. At this time the 250T is ready for binding. BOOK PREPARATION 3. Firmly hold sheets to be bound and place binding edge on lined surface. The first horizontal line above the paper will indic

The heat shoes can reach temperatures in excess of 300°F. • Keep hands and fingers away from the path of the sharp film cutter blade located at the film exit. • Do not place the laminator on an unstable cart, stand or table. An unstable surface may cause the laminator to fall resulting in serious bodily injury. Avoid quick stops, excessive force and uneven floor surfaces when moving the laminator on a cart or stand. »Do not defeat or remove electrical and mechanical safety equipment such as i

GBC se reserve le droit d’apporter des modifications a cette publication et aux produits qui y sont decrits sans preavis. Toutes les specifications et l’information au sujet des produits sont sujettes a changements sans preavis. Toute reference a l’information ou aux produits proteges par un droit d’auteur ou un brevet presentee dans ce document ne porte aucune licence sous les droits de GBC ou d’autres parties. GBC n’assume aucune responsabilite decoulant de contraventions aux brevets ou a tout

IN THIS INSTRUCTION MANUAL AND ON THE PRODUCT ARE IMPORTANT SAFETY MESSAGES HEAD THESE MESSAGES CAREFULLY. A THE SAFETY ALERT SYMBOL «m PRECEDES EACH SAFETY MESSAGE IN THIS INSTRUCTION MANUAL THIS SYMBOL INDICATES A POTENTIAL PERSONAL SAFETY HAZARD THAT COULD HURT YOU OR OTHERS, AS WELL AS CAUSE PRODUCT DAMAGE OR PROPERTY DAMAGE. THE FOLLOW(NG WARNING IS FOUND ON THE BOTTOM OF THE PRODUCT, A, A WARMING Elect Neal shacli huard. № nol open. No UQ«ir canjeable pftfts I n ii CfU- flelif SBrvic

Clay and ink affect this bond. While good adhesion occurs between molten adhesive and ink or clay, poor adhesion may exist between ink or clay and its parent paper. Accordingly, the lamination process will be adequate, but the overall laminate may lack some integrity. Some paper and card stocks are coated with silicones, wax, or varnish which inhibit the ability of molten polyethylene to stick tightly to individual paper fibers. In such cases, a superficial bond develops which may be adequate,

.. GBC4180 INTRODUCTION These instructions describe the use and function of two (2) laminators which, despite their varying widths, are similar in appearance and performance: MODELS FILM WIDTH GBC4120 12" (30 cm) GBC4180 18" (46 cm) GBC Laminators apply coated, transparent film to one but usually both sides of documents, photographs, or any sheet-like material. GBC laminating film consists of a polyester film coated one side with polyethylene-heat reactivatible adhesive. The film is applie

while ffrmiy puiiinq ism out the rea^ of îne ¡am:nator Ciontmue pi;* .iH'j the Mrr u.nt-i : ijfVA.nor>completely from the rotie's At ihis point you w^i iee ^ rnorr.^ni^'y lightening o* tension, to* owed r;y a si-o^g i>-:i m the opposite ejection 3 Release the reverse swuch. an^ r.jn tnt1- ia^ nator forward cntil ai* wnnk.ed filrr* exit^out t*v- rear NOTE: If film is wrapped arourvj the pultrolier!, does not extend out the rear of the larnnatof re^vicw the top iiim supply roll, and pofi the

IN THIS INSTRUCTION MANUAL AND ON THE PRODUCT ARE IMPORTANT SAFETY MESSAGES. READ THESE MESSAGES CAREFULLY. A THE SAFETY ALERT SYMBOL PRECEDES EACH SAFETY MESSAGE IN THIS INSTRUCTION MANUAL. THIS SYMBOL INDICATES A POTENTIAL PERSONAL SAFETY HAZARD THAT COULD HURT YOU OR OTHERS, AS WELL AS CAUSE PRODUCT DAMAGE OR PROPERTY DAMAGE. THE FOLLOWING WARNING IS FOUND ON THE BOTTOM OF THE PRODUCT. WARNING Electrical shock hazard. Do not open. No user servicable parts inside. Refer servicing to quoNli