.. GBC4180 INTRODUCTION These instructions describe the use and function of two (2) laminators which, despite their varying widths, are similar in appearance and performance: MODELS FILM WIDTH GBC4120 12" (30 cm) GBC4180 18" (46 cm) GBC Laminators apply coated, transparent film to one but usually both sides of documents, photographs, or any sheet-like material. GBC laminating film consists of a polyester film coated one side with polyethylene-heat reactivatible adhesive. The film is applie

Punching the Paper For the C340, always make sure that the punch handle is in the upright position before centering the paper. Load the first paper stack into the punch slot. Center the paper using the dial located at the front of the machine. Lower the raised handle until the paper is punched, and support the machine when lifting the handle to the upright position (Fig.4-A). For electric punching with the C450E: Load the first paper stack into the punch slot. Center the paper using the dial loc

• Die Steckdose sollte sich - gut zuganglich -in der Nahe des Gerats befinden. • Der Erdungsstecker dient zur Sicherheit und pa.t nur in ordnungsgema. geerdete Netzsteckdosen. Wenn der Stecker nicht in die Steckdose pa.t, lassen Sie sich von Ihrem Elektriker eine passende Steckdose installieren. Nehmen Sie keine Anderungen am Netzstecker (falls mitgeliefert) des CC2700 vor, denn er dient zu Ihrer Sicherheit. • Stecken Sie den CC2700 aus, wenn Sie den Standort der Maschine verandern oder wenn die

Excluded from warranty are the dies which are subject to wear. GBC will repair or replace at our option the unit free of charge and return it prepaid. Please include a copy of your paid invoice. Any unit sent without proof of purchase will not be serviced free of charge. Instead such units will be serviced at the prevailing rates and returned C.O.D. This warranty does not extend to any GBC machine that has been subject to misuse, neglect, accident, or if the serial number has been altered or d

GBC 1264WF/1244WF Operation Manual © 2006 General Binding Corporation Page 18 Display Control Panel-Continued Top and Bottom Temperature Use the up or down arrow keys to increase or decrease the set temperature of the heat rollers. The temperature shown on the display is the temperature at which the unit is attempting to attain. For example if the unit is set to 200*F even though the actual roller temperature may be higher or lower. To view the actual temperature press MEASURE. Stop The STOP but

Step 4. Figure 2 STAND BY CLEAR COUNTER START OPEN CLOSE NOTCH FUNCTION READY MANUAL AUTO PAD EMERGENCY 1 2 9 8 7 6 3 4 5 10 1 2 9 8 7 6 3 4 5 10 No. Symbol Function LED Display / Symbol Example 1 EMERGENCY Stops all the actions of the machine. Except when “HOT” shows on the LED display. “STOP” (flashing) 2 STAND BY / LED Temporarily lowers the temperature of glue tank so it won’t burn the glue when the machine is not operated. STBY00 3 CLOSE Closes clamp. 4 LED DISPLAY 1. The amount of books bo

Der Betrieb eines solchen Gerats in einem Wohngebiet wird wahrscheinlich Storstrahlungen verursachen, in welchem Fall der Benutzer diese Storungen auf seine eigenen Kosten beheben mu.. ACHTUNG: VERANDERUNGEN, DIE NICHT AUSDRUCKLICH VON DER GENERAL BINDING CORPORATION GENEHMIGT WERDEN, KONNTEN IHRE BEFUGNIS ZUM BETRIEB DIESES GERATS NICHTIG MACHEN. Dieses Digitalgerat der Klasse A entspricht allen Anforderungen der kanadischen Bestimmungen fur Storstrahlungen verursachende Gerate. FCC NOTE FCC NO

5. Insert the carrier and its contents straight into the machine, leading with the folded edge. handle carriers carefully so that they can be reused. REV Selecting Functions} } Control Panel LCD 13 Pro Operating Instructions PRE/H Stand-by 6 The laminated item will automatically exit the rear of the pouch laminator. After the pouch has stopped moving, place the carrier on a flat surface to cool briefly before removing the finished pouch. 7. If the laminated product looks hazy, then the temperatu

MAIN ON/OFF SWITCH (Fig. 9– Item W) The Main On/Off Switch supplies power or removes power from the machine. FUSES (Fig. 9– Item X) The Fuses protect internal PCB’s and motors. POWER CORD (Fig. 9– Item Y) The Power Cord plugs into the Main Power source or outlet. See (Machine Specs for plug requirements.) LOCKING PINS (Fig10– Item Z) The Locking Pins secure the Film Shaft Latch. FILM SHAFT LATCH (Fig. 10– Item A1) The Film Shaft Latch secures the Supply shaft ensuring that the film is supported

(Text Box comment Office Zone) (Text Box comment 800.543.5454) (Text Box comment ProClick Pronto® ™™™™™ ENG ProClick Pronto® ™™™™™ ENG 1.1 Safety Messages 1.0 Safety The safety of you and others is very important to GBC. Important safety messages and information are contained within this manual as well as on the machine itself. Please be certain to carefully read and understand all of these before operating the machine. The safety alert symbol precedes each safety message in this Operating Instr