Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Panasonic Dateigröße: 4.63 mb Dateiname: estudio_520_600_720_850.pdf Unterrichtssprache:

• The finisher for this high-speed equipment quickly finishes complex sorting or mass-copying. 9 General Precautions When installing or moving Warning • This multifunctional digital systems requires 115 V, 20 A, 50/60 Hz electric power. Do not use a power supply with a voltage other than that specified. Avoid multiple connections in the same outlet. This could cause a fire or give you an electric shock. If you are considering increasing the number of outlets, contact an electrician. • Always connect this multifunctional digital systems to an outlet with a ground connection to avoid the danger of fire or electric shock in case of short-circuiting. Contact your service representative for the details. Be sure to use a 3-conductor, grounded wall outlet. In areas, except U.S. and Canada, where a 2-pin plug is used, the multifunctional digital systems must be grounded for safety. Never ground it to a gas pipe, a water pipe, or any other object not suitable for grounding. • Plug the power cord securely into the outlet. If it is not plugged in properly, it could heat up and cause a fire or give you an electric shock. • Do not damage, break or attempt to repair the power cord. The following things should not be done to the power cord. -Twisting it -Bending it -Pulling it -Placing anything on it -Making it hot -Situating it near radiators or other heat sources This could cause a fire or give you an electric shock. If the power cord is damaged, contact your service representative. • When removing the plug from the outlet, do not pull the power cord. Always hold the plug when removing it from the outlet. If the power cord is pulled, the wires may become broken and this could cause a fire or give you an electric shock. • Make sure that the ventilation holes are not blocked up. If the temperature within the multifunctional digital systems becomes too high, a fire could result. • Do not move the multifunctional digital systems to another building, up and down the stairs or for any great distance. This could cause an injury or give you and electric shock. When lifting or moving the multifunctional digital systems, contact your service representative. • Do not move the multifunctional digital systems with optional equipment, such as the finisher, attached. This could cause a fire or give you an electric shock. When lifting or moving the multifunctional digital systems, contact your service representative. • When moving the multifunctional digital systems, be sure to shut down the power prior to pulling out the plug from the outlet. If the power cord is damaged, this could cause a fire or give you an electric shock. • The socket outlet should be near the equipment and be easily accessible. • Pull out the plug from the outlet more than once a year to clean around the prongs. Accumulating dust and dirt could cause a fire due to the heat released by electric leakage. 10 Caution • Do not tilt the multifunctional digital systems more than 10 degrees when moving it. If it falls, this could result in personal injury. • Avoid placing the multifunctional digital systems in a place unsuitable for its weight and also make sure the surface is level. Remember that if the multifunctional digital systems falls over, serious injuries could result. Weight of the multifunctional digital systems: approx. 463 lb. • There are 4 adjusters (stoppers) at the bottom of the equipment (2 in the rear, 2 in the front). After moving/ installing the equipment, be sure to turn and lower the adjusters, and then fix them firmly on the floor. Before moving the equipment, turn and raise the adjusters. • When connecting the optional equipment and interface cable to the multifunctional digital systems, be sure to turn the power OFF. If the power is not turned off, you could get an electric shock. To turn the power OFF, see .. P.30 “Shutdown”. 11 General Precautions (Cont.) Other points • Make sure that there is enough space around the system to facilitate changing of parts, maintenance and clearing paper jam. If there is insufficient space, some operations, such as bypass feeding, will become difficult and the multifunctional digital systems could even break down. 2788 mm (109.76") 1455 mm (57.28") 1548 mm ( 60.94" ) 100 mm (3.9") 1024 mm (40.3") • Be sure to fix the power cable securely so that no one trips over it. • Adverse environmental conditions may affect the safe operation and performance of the multifunctional digital systems, and the multifunctional digital systems could break down. -Avoid locations near windows or with exposure to direct sunlight. -Avoid locations with drastic temperature fluctuations. -Avoid too much dust. -Avoid location that suffer from vibration. • Allow the air to flow freely and make sure there is a ventilator. With inadequate ventilation, the unpleasant odor released by ozone will begin to dominate the atmosphere. 12 When using the multifunctional digital systems Warning • Do not place metallic objects or containers with water ...

Herunterladen

Geben Sie zwei Ziffern: