The yellow light will be on and the meter will indicate low current. BATTERY CHARGE - After testing the battery, the control will select a charging rate suitable for the voltage and state of charge of the battery. A small battery, or a nearly charged battery will cause the charger to rapidly step down in current to avoid heating and gassing. FINISH CHARGE - In order to reach a 100 % state of charge on the battery, a 3 hour finish cycle has been programmed into the charger control. During this cy

e. NEVER smoke or allow a spark or flame in vicinity of the battery or engine. f. Be extra cautious to reduce risk of dropping a metal tool onto the battery. It might spark or short circuit the battery or other electrical parts that may cause an explosion. g. Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery. A lead-acid battery can produce a short circuit current high enough to weld a ring or the like to metal, causing a severe bu

Do not operate charger in a closed-in area, or restrict ventilation in any way. e. Do not set a battery on top of charger. 16. DC CONNECTION PRECAUTIONS a. Connect and disconnect dc output clips only after setting any charger switches to off position and removing ac cord from electric outlet. Never allow clips to touch each other. b. Attach clips to battery posts and twist or rock back and forth serval times to make a good connection. This tends to keep the clips from slipping off terminals and

! Start the vehicle with the charger connected to the battery. NOTE: Do not crank the engine more than 20 seconds in any five minute period; excessive cranking may overheat and damage the starter. If the vehicle fails to start, while waiting for the starter to cool, allow the charger to continue to charge the battery. Unplug the charger before disconnecting dc clips from battery. POSSIBLE CHARGING PROBLEMS: 1. ! Meter needle swings to far right side of meter: (Manual). ! Reverse connection indic

9014 — SELECT SETTING switch with the following selections; OFF, 10A–12V AUTO, 2A–12V AUTO and 10A–6V MANUAL 9060 — SELECT SETTING switch with the following selections; 55A START, 10A–12V, 2A–12V and 10A–6V MANAUL — SELECT FUNCTION switch with following selections; CHARGE and START — Charge Complete Indicator light. — Reverse connection indicator light. 9070 — SELECT SETTING switch with the following selections; 70A START, 12A–12V, 2A–12V and 12A–6V — SELECT FUNCTION switch with following select

The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. DANGER. Never alter AC cord or plug provided - if it will not fit outlet, have proper outlet installed by a qualified electrician. Improper connection can result in a risk of an electric shock. This battery charger is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in FIGURE (A). A temporary adapter, which looks li

Insulated fiberglass backboard with 10 pairs DC charging leads, 10 gauge, 36” long with 300 Amp insulated safety clamps. Comes with three-foot 4 AWG cables to connect to charger or additional bus bars. Model 6086 Battery Charging Rack Battery charging rack stores up to 15 batteries. Convenient three-shelf, heavy-gauge steel construction rack with 10 pairs of charging leads. Insulated storage bars and connections ensure there are no live electrical connections. Shelves have durable 1/8” polypro

The second stage is a slow charging to restore the battery to full charge. READ AND FOLLOW ALL PRECAUTIONS AND WARNINGS IN YOUR INSTRUCTION MANUAL BEFORE ATTEMPTING TO CHARGE SULFATED BATTERIES. FAILURE TO OBSERVE THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE OR SERIOUS PERSONAL INJURY OR DEATH. To recharge a sulfated battery: 1. Attach the battery clamps as described in the instruction manual. 2. Always use the chargers lowest rate when turning the charger on. Set the charger to the chargers hig

DANGER. Before using adapter as illustrated, be certain that center screw of outlet plate is grounded. The green-colored rigid ear of lug extending from adapter must be connected to a properly grounded outlet, make certain it is grounded. If necessary, replace original outlet cover plate screw with a longer screw that will secure adapter ear lug to outlet cover plate and make ground connection to grounded outlet. MOUNTING: The Battery Charger may be set on a table or a shelf. Do not set charger

This manual contains important safety and operating instructions for battery charger you have purchased. You may a later date. 2. CAUTION. To reduce risk of injury, charge only wet cell, lead-acid, automotive type rechargeable batteries. Other types of batteries may burst causing 3. Do not expose the charger to rain or snow if specifically warned on the unit not to do so. 4. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric sh