REPLACING THE GREASE FILTER 1. Push the wire clips to one side and remove (Fig.10). Fig.10 2. Remove the saturated grease filter. 3. Place the new grease filter in the filter grille (Fig.11). Fig.11 4. Replace the retaining clips. 5. Close the grille panel. THE CARBON FILTER ( Recirculation only) The activated carbon filter absorbs odours arising from the cooking. In use, the filter will slowly become saturated and gradually less effective. The filter will normally require changing every four mo

The cut-out device will reset itself when the fan motor has cooled significantly. NOTE: This hood has been designed and approved for installation over an electric hob with a maximum input of 7kW or a gas hob with a maximum input of 10kW when fitted in accordance with the heights recommended above. Your Cooker Hood can be installed either for recirculation back to the room or extraction through an outside wall. When used in the extraction mode the Cooker Hood ducting must not be connected to a fl

Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local electricity company regulations. For your own safety, this should be undertaken by a qualified electrician eg. your local electricity company or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown

Fix the wall brackets. 2. Fix the canopy hood. 3. Connect the hood to the mains supply ensuring that the canopy is functioning correctly. 4. Select the type of installation, ie. ducting or recirculation. 5. Fix the chimney stack. NOTE: The hood is more efficient in the exhaust mode, therefore, this position should be selected during the warmer months of the year when no heating is being used. When the room is being heated, if the recycle position is selected heat will not be wasted. Installing y

Do install the hood at the correct height, allowing at least the minimum distance above a cooking appliance (see page 5). Fan Speed The right slider enables you to select the fan speed. Your Cooker Hood has three speeds to give you the correct extraction level to suit your cooking conditions. Position 1 should be selected when simmering or when using only one pan. Position 2 should be selected for normal cooking up to four pans. Position 3 should be selected when frying or cooking food with stro

The hot interior of the heater can produce paraffin smells from polish vapours which may last for a number of hours. »DO NOT ATTEMPT TO REPAIR THE HEATER YOURSELF. In case of breakdown or other failure, switch off the heater at the wail switches and consult your supplier, local electricity company or Applied Energy Products Ltd. Always ensure that the heater is switched off at both wall switches and the fuses removed before any repair is carried out. HOW IT WORKS: This heater stores heat on

Nos; 5FH18AVV SFH24AW OWfiefS Guido IMPORTANT INSTRUCTIONS Retain these instructions for future reference, recid them carefully and note also the information given on the heater. IMPORTANT SAFETY INFORMATION WARNING * THE SURFACE OF THIS HEATER CAN BE HOT. The 5uncice temperatures of this heater are within the requirements of EN60-335 the European Standard covering the safety requirements of electric storage heating appliances, and momentary contact with any part of the heater should not ca

Able to regulate input with direct acting heat flexibility, the SFHA Sensair is more effective at retaining heat than a conventional storage heater. ” Able to operate on virtually any tariff and with superior high performance insulation levels, it achieves higher SAP and NHER ratings than manual input storage heaters. Key features • Combines electric storage fan heating, direct acting heating and fanned heat output with simple controls • Fully automatic heat storage - no user adjustment required

* TSR6AW/MW have no user controls and are IPX2 rated (drip-proof) ChargeCharge Acceptance (7 hrs)Acceptance (8 hrs) • Elements (storage) - mineral insulated stainless steel sheathed • Insulation - opacified silicaceous aerogel and mineral fibre mat • Storage Core - high density iron oxide compound • Controls* (Output) - manually adjustable thermostat controlling output damper. • Controls (Input) - hydraulic charge control thermostat, manually adjustable • Protection - two level thermal safety ov

Nos: TSR12CW TSR18CW TSR24CW TSR12ACW TSR18ACW TSR24ACW C( This appliance conforms to îhe following EEC Directives: low Voltage Equipmenl Electromagnetic Compatibility 73/23/EEC 89/336/EEC 93/68/EEC 92/31 /EEC 93/68/EEC IMPORTANT NOTES: It is important to read these instructions carefully and also note the information given on the heater itself. As these particular instructions refer to the assembly and installation of a new heater, they should be retained by the installer; not left behind