Stimmen - 3, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
REPLACING THE GREASE FILTER 1. Push the wire clips to one side and remove (Fig.10). Fig.10 2. Remove the saturated grease filter. 3. Place the new grease filter in the filter grille (Fig.11). Fig.11 4. Replace the retaining clips. 5. Close the grille panel. THE CARBON FILTER ( Recirculation only) The activated carbon filter absorbs odours arising from the cooking. In use, the filter will slowly become saturated and gradually less effective. The filter will normally require changing every four months, depending on the amount and type of cooking you have done. See page 5 (Figs. 1 and 2) to set your Cooker Hood to the recirculation option. TO FIT THE CARBON FILTERS The deflector should be fixed to ensure the air flow is away from the wall to avoid dirtying or marking the rear wall (Fig.12) . Fig.12 Place the new carbon filter, ensuring that it is aligned. to lock the filter turn in the direction of the arrow (Fig.13) Fig.13 The Hood must not be connected to ducting when in the recirculating mode. Regular replacement of the charcoal filter will ensure optimum performance from the hood when recirculating. TO REPLACE THE CARBON FILTER Remove the grille by turning the locks and pull the grille out and downwards. Remove the saturated carbon filter by rotating it in an anti-clockwise direction and replace it with a new one. Caring for your Cooker Hood Cleaning: The exterior of the Cooker Hood should be cleaned regularly to keep it looking like new. Wipe over with a soft cloth, wrung out in warm water and dry with a clean soft cloth. Wear protective gloves. You can use mild non-abrasive cleaners but always read the manufacturer’s instructions first. Always test their suitability on a small area of the Cooker Hood not noticeable in normal use. NOTE: DO NOT use scouring pads or abrasive cleaners as they may scratch the surface. How to replace the light: Should the light fail to work,switch ‘Off’the mains supply to the Hood. Open the grille and check the bulb is screwed securely into the bulb holder then switch ‘On’ the mains supply. If the light fails to work do not worry, it will not affect the working of your hood. Obtain a replacement 40 watt (E14) bulb. Switch ‘Off’ the mains supply. Unscrew the old bulb anti- clockwise to remove and replace with the new bulb turning clockwise until secure. Refit the filter grille and switch back ‘On’ at the mains. NOTE: When changing the bulb, an identical replacement must be fitted to ensure the safe operation of the hood. Fig.14 Troubleshooting. First, don’t panic! There may be nothing wrong at all. Look for your problem below, then check the things we suggest. More often than not, this will give you the answer to your problem, and you’ll be able to carry on without having to telephone your Service Office. It is not working! Are you using a plug and socket? -Check that the plug is firmly pushed in. - Check the power supply, by plugging in another appliance. - Has the fuse blown? It is not working! Is the mains lead wired directly into a double pole isolating switch? -Check that the wires in the mains lead are correctly connected. (See page 2) The Cooker Hood is not working satisfactorily... - Check you have selected the correct fan speed. (See page 8) - Check you have left the cover over the recirculation grille on top of the Hood (extraction only), (See page 6). - Check if the grease filter needs replacing (See page 9). The light is not working... - Check the bulb is screwed in securely. - Replace the light bulb (See page10) The Cooker Hood switches off intermittently... - Check the mounting height above the hob is correct (See page 5). The heat from the hob may cause the fan motor to overheat/cut-out. If, after following these instructions, you are still having problems, contact your nearest Service Centre (See back cover). Parts Please remember your new appliance is a complex piece of equipment. Repairs may only be performed by qualified technicians. ‘DIY’ repairs or unqualified and untrained service people may put you in danger, could damage the appliance and might mean that you lose cover under the Guarantee. If you do experience a problem with the appliance, don’t take any risks, call in a Service Engineer (See back cover). Our Parts are designed exclusively to fit only GDA Ltd appliances. Do not use them for any other purpose as you may create a safety hazard. Key Contacts Service Creda has the largest appliance manufacturer’s service team in Europe, trained specialists directly employed by us to ensure your complete confidence. Repair Service UK: 08709 066 066 Republic of Ireland: 1850 302 200 You will be asked for the following information: Name, address and postcode. Telephone number Model / Serial number of the appliance Clear and concise details of the query or fault Place and Date of purchase (Please keep the receipt as evidence will be required when the engineer calls). Extended Warranty To join: UK 08709 088 088 Republic of Ireland: 1850 502 200 Genuine Parts & Ac...