Folgende Daten beim Anruf angeben: 1. Modellbezeichnung 2. E-Nr. 3. F-Nr. Diese Daten befinden sich auf dem Typenschild auf der Innenseite des Gerates hinter den Fettfiltern. Konstruktions- und Farbanderungen im Rahmen der technischen Entwicklung bleiben vorbehalten. SERVICE Handelt es sich um eine technische Storung? Dann wenden Sie sich an Ihre Kundendienststelle. (Adressen und Telefonnummern befinden sich im Abschnitt „Kundendienststellen“.) Bereiten Sie das Gesprach in jedem Fall gut vor. Si

Afb. 12a-b Als u de wasemkap wilt gebruiken als filterend apparaat, bevestig aan de draagbeugel de luchtgeleider en het andere uiteinde van de pijp aan de aansluitring aanwezig op de luchtgeleider. Afb. 12c afb. 12a afb. 12b afb. 12c • Maak de elektrische aansluiting. • Laat het onderste schouwdeel dalen om de afzuiggroep helemaal af te dekken, totdat hij goed op zijn plaats boven de wasemkap zit. Afb. 13a • Breng de bovenste schouwdeel aan en zet hen aan de bovenkant vast met 2 schroeven aan de

• Tighten the 4 screws (7). • Insert and tighten another 2 screws in the remaining free holes (8) for secure fixing. • Carry out the electrical connection (9) to the mains power supply, only turn on the power supply upon completion of assembly. • Hook the hood onto the truss (10) , ensuring it fits properly – to hook the hood onto the truss partially tighten 4 screws (see also step 12). • Secure the hood to the truss using two screws (11); this will also help center the two sections. • Tighten t

Rotate motor upwards until it snaps into the spring clip on the right. Secure the motor to the hood with the machine screw and lock washer. Plug connector into the motor, Fig. 11. From Control Panel Motor connector FIG. 11 FIG. 10 Spring Clip Outlet Bracket Motor Connector Spring Clip Motor support Fixing point Fixing point Bracket Integral ventilator for 40" Hood 11 INSTALLATION 12 2. Snap the central baffle filter panel into the place so the both rails engage with side pins on both sides of ho

DCS offers both a 6” and 12” height Duct Covers. Keep the 6 or 12 inch dimension in mind when allowing for clearance between the top of the Vent Hood and the ceiling. (see Fig. 4) 1. With the Vent Hood width, and installation site in mind, mark the centerline of the installation. 2. See the chart in Fig.4 to determine the centerline to centerline dimension of wall mounting holes for the particular model being installed. 3. Cut away enough drywall (if installed) to expose 2 vertical studs (1 on e

Provide him with the Model Number, Serial Number, and date of installation, and a brief description of the problem. If you need assistance in locating the authorized service agency in your area please contact our DCS Customer Service Department for an authorized service agent near you, our number is (888) 281-5698. Your satisfaction is of the utmost importance to us. If a problem cannot be resolved to your satisfaction, please write or fax us at: Write: Dynamic Cooking Systems, Inc. Attention: C

THE PROFESSIONAL VENT HOODS Use and Installation Guide Models: • DCS-VH-48HS • DCS-VH-48S • DCS-VH12-36HS • DCS-VH12-36S • DCS-VH-36HS • DCS-VH-36S • DCS-VH-30HS • DCS-VH-30S A Message To Our Customers A Message To Our Customers Thank you for selecting this Dynamic Cooking Systems Professional Vent Hood. Because of its unique features, we have developed this Use and Installation Guide. It contains valuable information on how to properly operate and maintain your new Vent Hood for years of safe a

Cold weather installations necessitate the use of a backdraft damper to minimize the flow of cold air into the room. A nonmetallic thermal break should also be installed to minimize conduction of outside temperatures through the ductwork. Locate the thermal break as close as possible to where the ducting enters the heated portion of the house. PLANNING THE INSTALLATION: Before beginning installation of the Vent Hood and Ventilator, PLAN OUT the entire installation procedure beforehand, consideri

Dispose carefully of the packaging material so that it is out of the way of small children. Position The cooker hood should be mounted freely hanging on the wall. The cooker hood must be at least 60 cm above electric hobs or electric ranges, or at least 70 cm above gas burners or gas ranges. The cooker hood cannot be connected to flues of other appliances that run on energy sources other than electricity. Please, keep to the provisions of official directives regarding fume discharge. Electrical

Never use caustic detergents or abrasive brushes or powders. Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. Attention! Attention! Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. 40 MKZ telescopic wall pipe 120 mm outlet hose KLF60/80 activated carbon filter E-Nr. 610 899 004 610 899 007 610 899 421 Technical assist